9" Color TV
(160-0246A)                Operation                  Faxback Doc. # 6772

USING THE REMOTE CONTROL

To use the remote control, point it toward the TV and press the desired
button.

Before operating your TV, complete the necessary connections described in
Faxback Document # 6771.

PROGRAMMING THE TUNER MEMORY

You can program the tuner's memory so when you press CHANNEL down arrow or
up arrow the TV scans only the channels used in your area.

1.  Press TV/CATV on the remote control to select the type of signal you
    receive.  If you are using an antenna, select TV; if you have cable,
    press TV/CATV until STD, HRC or IRC shows on the display for the cable
    service type.

NOTE:  STD is used by most cable systems.  If the STD setting does not
       work with your TV, try the other two settings and/or check with 
       your cable service provider.

2.  Press AUTO MEMO on the remote control.  The TV's tuner scans the
    entire range of the selected band (TV or CATV) and memorizes all
    the active channels in your area.  After scanning all the channels,
    the tuner stops on the previously selected channel and SKIP appears
    on the screen momentarily to indicate the TV skipped all inactive
    channels.

3.  Press either CHANNEL up arrow or down arrow to check the channels
    stored in the memory.

NOTES:  The on-screen channel is color coded and displays in either red or
        green.  Green indicates a channel that is active or programmed in
        memory.  Red indicates a channel that is inactive or has not been
        programmed.

        If there are no channels stored in memory, you can scan for any
        active channels using CHANNEL down arrow or up arrow.  You can
        also select any active channel directly using the remote control's
        number buttons.

        To change channels more quickly when using the number buttons,
        precede one-digit channel numbers with a zero (02, 03, 04 and so
        on).  To select a channel over 99, select the CATV mode, press
        100, and then enter the channel number.

Erasing or Adding Channels

To erase channels from or add channels to the programmed channels, do the
following:

1.  Select the desired channel using the CHANNEL up arrow or down arrow
    or the remote control's number buttons.

2.  To erase a channel, press WRITE/ERASE on the remote control until the
    channel number displayed on the screen turns red.  To memorize a
    channel, press the button until the channel number turns green.


WATCHING BROADCAST OR CABLE TV

1.  Press in POWER to turn on the TV.

2.  Press TV/VIDEO so a channel number displays on the TV.

3.  Press CHANNEL up arrow or down arrow to receive the desired station.
    Or use the remote control number buttons to directly select a 
    channel.

4.  Press VOLUME up arrow or down arrow to adjust the volume.

5.  To turn off the TV, press POWER.

Adjusting the Picture

All picture controls (contrast, brightness, color, tint, and sharpness) on
the TV are initially set to the center position.  You can adjust the
individual settings using the remote control.

1.  Press PICTURE SELECTOR on the remote control until the desired control
    appears on the screen.

2.  Press down arrow or up arrow to adjust the control as indicated in the 
    chart below.

    Picture Control       Up         Down
    Adjustment          Arrow        Arrow

    Contrast            Lighter       Darker
    Brightness          Darker       Brighter
    Color               Lighter      Deeper
    Tint                Purplish     Greenish
    Sharpness           Softer       Sharper

NOTES:  To restore all controls to their factory settings, press
        MUTE/RESET while any control appears on the TV.

        If you accidentally press the VOLUME up arrow/down arrow, 
        CHANNEL up arrow/down arrow or PICTURE SELECTOR up arrow/down
        arrow buttons at the same time on the TV, the TV enters the
        TEST 1 mode.  The TEST 1 mode is only for factory adjustment
        and has no user function.  To return the TV to its normal
        settings, press MUTE/RESET so TEST 1 disappears from the screen.


Using Mute

Press MUTE/RESET on the remote control to temporarily turn off the sound. 
The volume indicator appears on the TV with the marker at the far left. 
To restore sound, press MUTE/RESET again.  The volume indicator appears
again, with the marker set to its previous position.


Using Quick View

Press QUICK VIEW to switch between the current channel and the previously 
viewed channel.


CONNECTING AN EARPHONE

The earphone jack allows you to connect an earphone (such as Cat. No.
33-175, not supplied) with a 1/8-inch mini-plug so you can listen to the
TV privately without disturbing others.  Simply insert the earphone into
the jack on the left side of the TV.  This automatically mutes the TV's
speaker.

Listening Safely

To protect your hearing, follow these guidelines when you use an earphone.

Set the TV's volume to the lowest setting before you begin listening. 
After you begin listening, adjust the volume to a comfortable level.

Do not listen at extremely high volume levels.  Extended high-volume
listening can lead to permanent hearing loss.

Once you set the volume, do not increase it.  Over time, your ears adapt
to the volume level, so a volume level that does not cause discomfort
might still damage your hearing.

USING THE TV AS AN AUDIO/VIDEO MONITOR

Follow these steps to use the TV as a color monitor when you connect an
audio/video device.

1.  Turn on the TV.

2.  Turn on and start the audio/video device.

3.  Press TV/VIDEO on the remote control to select which input signal you
    view.   VIDEO 1 or VIDEO 2 appears briefly on the screen.

(CJD/all-6/30/94)

Privacy Policy