Model 36 9" Color TV/ VCR Combo
(160-0429)                 Operation - TV             Faxback Doc. # 50430

BASIC TV OPERATION

SELECTING CHANNELS

To select a channel, press CHANNEL /\ or \/.  The tuner automatically
advances to the next channel stored in the tuner's memory.

Note:  If you press CHANNEL /\ when the tuner is at the highest programmed
       channel or CHANNEL \/ when the tuner is at lowest programmed
       channel, the Model 36 enters the audio/video mode and AUX appears
       (see "Viewing an External Device" below).  If you press CHANNEL /\
       or \/ again, the Model 36 tunes to the lowest or highest programmed
       channel.

       You can also select channels directly using the number keys on the
       remote control.  You can choose any channel in the tuner's range,
       even if you have not programmed the channel, there is no broadcast
       present, or the channel is scrambled (the tuner does not unscramble
       the channel).

Notes:  Precede a single-digit number with a 0 - for example, 01, 02, and
        so on.

        If you selected the CATV input signal (see "Selecting the Input
        Signal" in Faxback Doc. # 50429), press +100 on the remote control
        to enter the first digit of a 3-digit channel number.  Then use
        the number keys to enter the second and third digits.

VIEWING TV

Follow these steps to view a broadcast using the TV.

1.  Press POWER to turn on the Model 36 if necessary.

2.  If you have not already done so, select the desired input signal (TV
    or CATV).  See "Selecting the input Signal" in Faxback Doc. # 50429.

3.  Select the channel you want to watch.

4.  If you are using the indoor antenna, extend and rotate it to get the
    best reception.

    Note:  To improve UHF reception, shorten the indoor antenna.

5.  Repeatedly press VOLUME /\ or \/ to adjust the volume to your
    listening preferences.  A bar graph and a number appear, showing the
    currently set volume.

ADJUSTING THE PICTURE

Follow these steps to adjust the picture's brightness, contrast, color,
tint, or sharpness.

1.  Press MENU to select the main menu.

2.  Press PLAY/ /\ or STOP/ \/ to select PICTURE CONTROL, then press
    F.FWD/>.  BRIGHT and a bar appear.

3.  Repeatedly press PLAY/ /\ or STOP/ \/ within 5 seconds until the
    setting you want to adjust (brightness, contrast, color, tint, or
    sharpness) appears.

    Note:  If you do not press PLAY/ /\ or STOP/ \/ within 5 seconds, the
    displayed setting disappears.  Start over at Step 1.

4.  Within 5 seconds, repeatedly press REW/< or F.FWD/> to adjust the
    displayed setting.  A bar appears, showing the current setting.

      Setting                REW/<                   F.FWD/>

      BRIGHT                 to                      to
                             decrease                increase

      CONTRAST               to                      to
                             decrease                increase

      COLOR                  toward                  toward
                             pale                    brilliant

      TINT                   toward                  toward
                             purple                  green

      SHARP-                 toward                  toward
      NESS                   soft                    clear

    To quickly change the displayed setting, hold down REW/< or F.FWD/>.

    If you do not press REW/< or F.FWD/> within 5 seconds, the displayed
    setting disappears.  Start over at Step 2.

5.  Either wait 5 seconds or press MENU to exit.

USING MUTE

To temporarily turn off the Model 36's sound, press MUTE.  MUTE and the
volume level bar appear.

To restore the sound to the previous level, press MUTE again.  To restore
the sound and change its level, press VOLUME /\ or \/.

USING CHANNEL RETURN

The Model 36's channel return function lets you quickly switch between
channels you tuned (including AUX, see "Viewing an External Device",
below) by using the remote control's number buttons.

Repeatedly press CHANNEL RETURN on the remote control to switch from the
channel you are watching to the previous channel you tuned, and vice
versa.

VIEWING AN EXTERNAL DEVICE

To view the signals from an external device you connected to the audio/
video input jacks on the front of the Model 36 (see "Connecting an
External Device" in Faxback Doc. # 50428), do either of the following:

  Enter 00 using the remote control's number buttons.

  Select one channel higher than the highest programmed channel or one
  channel lower than the lowest programmed channel.

AUX appears on the TV screen.

(LB/eb 10/16/98)