RCA CC645 VHS CAMCORDER
(160-0869) Optional Accessories Faxback Doc. # 45387

We invite you to take a look at some great ideas for sparking creativity
and adding to the fun of using your compact VHS camcorder. The following
pages have a selection of accessories to help make your memorable moments
look and sound even better.

These accessories are designed to make the process of recording and watch-
ing your videos more enjoyable.

To order accessories, contact your local Dealer.

Custom compact soft case designed especially to provide protection and
utility for your compact VHS camcorder and most accessories. Rugged fabric
fabric lined with soft non-abrasive material and generous padding. Has three outside pockets with storage for lens filters, adapters, batteries, and tapes.

This car cord adapter enables you to operate your camcorder from your car,
truck, or RV by plugging the car cord directly into the vehicle's cigarette
light socket. The DCC08 is designed specifically to convert power from a 12-volt battery to a 6-volt output.

These rechargeable nickel-cadmium batteries are designed specifically for
long life. The FB1260 is the same battery that came packed with your cam-
corder. The FB120 powers your camcorder twice as long as the FB1260 (with video light off depending on how much you use zoom and pause). Both can be recharged with the AC adapter/charger that came with your camcorder.

The CPS91 battery charger plugs directly into an AC outlet and charges the
FB1260 and FB 120 camcorder batteries. Because the CPS91 operates on 100-
240 Volts, 50/60 Hz, it can be used virtually anywhere in the world. A
plug adapter may be required in some countries. Charging takes approxi- mately seven hours for the FB1260 (1-hour battery) and 13 hours for the FB120 (2-hour battery).

Using The Optional AC088 Tripod

Mounting the camcorder on a tripod, such as AC088, will keep the camcorder
steady and produce excellent video results.

This tripod's fluid-effect head provides smooth camera pan and tilt.
The quick-release mount makes it easy to attach or remove the camcorder.
The grooved, tubular 3-section leg design folds down to 26" when not in
use. Rubber feet allow for sure footing.

CAUTIONS:

Before using a tripod, make sure it is stable enough to hold the
camcorder without falling over. Do not transport the camcorder
attached to the tripod.

When attaching your camcorder to a tripod, be careful not to force
the tripod screw into the camcorder's tripod mounting hole.

The tripod screw should not protrude into the camcorder more than
approximately three-eighth (3/8) inch. Forcing the screw could
damage the mounting hole on the bottom of the camcorder.

This RF output adapter is used with a coaxial RF cable, such as VH82 or
VH90, to connect your camcorder to a standard TV (one without audio/video
inputs) for playback. If your antenna cable is the flat twin-lead type
attached by two-screws, you will also need a 300-to-75 ohm transformer.
If your TV has 300 ohm antenna screw terminals, you will need an optional
75-to-300 ohm transformer such as VHF 54.

These RF cables are used with the RF output adapter to connect your
camcorder to a standard TV (one without audio/video input jacks) for
playback. If your TV has 300 ohm antenna screw terminals, you will need
an optional 75-to-300 ohm transformer such as VH54. If your antenna cable
is the flat twin-lead type attached by two screws, you will also need an
optional 300-to-75 ohm transformer.

This 75-to-300 ohm transformer is used connect a standard 75-ohm antenna
cable (such as VH82 or VH90) to the 300 ohm screw terminals on a TV.

This six foot audio/video cable can be used to connect the camcorder to a
TV monitor or VCR for tape playback or copying tapes.

This Y-adapter allows you to connect the camcorder's mono audio cable to a
TV or VCR.

All specifications and descriptions of accessories are subject to
change without notice.

(br/SM 11/14/97)