RCA CC645 VHS CAMCORDER
(160-0869)                 Remote Control             Faxback Doc. # 45126

Install Lithium Cell

The remote's lithium cell is packed separately.

Install it as follows:

CAUTIONS:

   Lithium cell battery.  Replace only with 3-volt lithium cell, such as
   CR2025.  Use of other cell presents a risk of fire or explosion.  Must
   be disposed of properly.  Never handle punctured or leaking cell.  May 
   cause burns or personal injury.

   Keep out of the hands of children.  Can cause death or injury if swal-         
   lowed.  If swallowed consult a physician immediately for emergency
   treatment.

   The lithium cell used in this device may explode resulting in a fire or
   chemical burn if mistreated.

   Do not recharge disassemble, heat above 212 degrees F (100 degrees C), 
   or incinerate.

   Never use metallic tweezers to hold the cell, and never short circuit 
   the + and - sides of the cell.

1.  Turn remote over, insert a pencil or paper clip in small hole, and
    remove battery holder.

2.  Insert battery in battery holder so positive (+) terminal faces up.

3.  Replace battery holder in remote until it clicks into place.

Notes:  Never place anything heavy on top of the remote control or play it
        upside-down.

Replace battery when camcorder fails to respond to remote.

Remove battery from remote if it will not be used for a month, or more.  This will prevent possible damage from battery leakage.  If leakage occurs, wipe up liquid inside compartment and replace battery.

Remote Sensor

The remote operates the camcorder by infrared light, so it is protected
from electrical and sound interference.  However, the remote must be aimed
directly at the camcorder's remote sensor.  There cannot be any
obstructions between them.

Note:  The camcorder may not respond to the remote if its sensor is exposed
       to direct sunlight or strong artificial light.

A brief description of the remote button's functions is given here.  Many
of the buttons perform the same functions as the corresponding controls on the camcorder.  The lithium cell must be installed as shown above.

A. (A (Audio) DUB Button

   Used for dubbing audio.  See Faxback Document #45408.

FF (Fast Forward) Button

   Camcorder's POWER switch in CAMERA:

   With camcorder in record pause, press and hold FF to visually search
   forward on the tape.  Release FF to return to record pause.

Camcorder's POWER switch in VCR.

   When the camcorder is stopped, press FF to fast-forward the tape.  Press
   STOP to stop forwarding the tape.

   When a tape is playing press and release FF to visually search forward 
   on the tape.  Press PLAY to return to normal playback.  For brief 
   searching, press and hold FF for at least two seconds to visually search
   forward.  Release FF to return to normal playback.

INSERT Button

   Used for edit inserting.  See Faxback Document #45408.

PAUSE Button

During playback, press PAUSE to produce a stop-action picture.  Press PLAY
or PAUSE to return to normal playback.

CAUTION:  Pause is designed for momentary interruptions and should not be
          used for an extended period of time.  If the camcorder remains in
          pause for more than five minutes, it will automatically enter the
          stop mode and then turn off.

PLAY Button

Press PLAY when the camcorder's POWER switch is in VCR to begin playback.

REW (Rewind) Button

Camcorder's POWER switch in CAMERA:

   When the camcorder is in record pause, press and hold REW to visually
   search the tape in reverse.  Release REW to return to record pause.

Camcorder's POWER switch in VCR:

   When the camcorder is stopped, press REW to rewind the tape.  Press STOP
   to stop rewinding the tape.

   When a tape is playing, press and release REW to visually search the
   tape in reverse.  Press PLAY to return to normal playback.  For brief
   searching, press and hold REW for at least two seconds to visually
   search in reverse.  Release REW to return to normal playback.

START/STOP Button

When the POWER switch is in CAMERA, press START/STOP to start and stop
recording.

Note:  If the camcorder is left in record pause for more than five minutes,
       power will turn off.

STOP Button

When the camcorder's POWER switch is in VCR, press STOP to stop playback,
rewind, or fast-forward operation.

TIME, LAPSE ANIM. (Animation)/REC TIME Button

When the POWER switch is in CAMERA, press to set amount of recording time
for interval and animation recording.

TIME-LAPSE SELF/INT. (Interval) TIME Button

When the Power switch is in CAMERA, press to activate the self-timer or
select an amount of interval time for interval recording.

ZOOM (T and W) Buttons

Camcorder's Power switch in CAMERA:

   Press T to move the lens in the telephoto (close-up) direction.

   Press W to move the lens in the wide-angle direction.

(br/SM 11/14/97)