Portavision
(160-0104) Operation Faxback Doc. # 40747
Select the desired power source and antenna.
1. Set the SELECTOR Switch 11 to TV.
2. Select the TV band with TV BAND Selector 16.
3. Tune slowly to the desired station by adjusting the TV TUNING
Control 17.
4. To obtain the best picture, adjust the BRIGHT 26 and CONTRAST
25 controls.
5. To obtain the desired sound level adjust the VOLUME Control 12.
NOTE:
To stop vertical "roll" of picture, adjust Vertical HOLD Control 24.
For horizontal "tear" of picture, adjust Horizontal HOLD Control 23.
Both Controls are located on the rear of the unit.
SPECIAL NOTE:
Since the TV set is continuously tuning, you may tune in some rather
strange sounds; this is normal and is actually a minor feature of this
type of tuning. You may be able to identify some of these unusual
signals.
POSSIBLE TV RECEPTION PROBLEMS
1. If the image is weak (with "snow") the signal reception may be
weak. This can be caused by your location-buildings made with a
large amount of steel can cause reception problems. Try changing
the position and length of the antenna. If this does not help,
use an outdoor antenna, especially if you are located far from the
TV station.
2. "Snow" along with "tear" or "roll" can often be due to improper
tuning. This can also be due to a very weak signal.
3. Tune slowly to the desired station with the RADIO TUNING Control
15.
4. Adjust the VOLUME Control 12 to the desired level.
RADIO OPERATION
Select the desired power source and antenna.
1. Set the SELECTOR Switch 11 to RADIO.
2. Set the RADIO BAND Switch 14 to FM or AM as desired.
3. Tune slowly to the desired station with the RADIO TUNING
Control 15.
4. Adjust the VOLUME Control 12 to the desired level.
POSSIBLE RADIO RECEPTION PROBLEMS
1. If FM reception is weak, this is generally caused by problems
similar to those described in "Possible TV Reception Problems".
Use an outdoor antenna for very weak stations.
2. If AM reception is weak, this may be due to distance of the
station or operation of the unit in a building with steel
construction. Turn the unit in different directions to find the
best position for the built in ferrite bar antenna.
CASSETTE RECORDER OPERATION
Press the EJECT Button 7 to open the cassette lid and insert the cassette
with its full reel on the left and opening towards the front.
PLAYBACK:
Set the function SELECTOR 11 to the "TAPE" position and depress the
PLAYBACK Button 6.
FAST Forward:
To skip over segments of tape, press the FAST Forward Button 5, then
the tape will wind forward quickly.
REWIND:
To return to a previous segment of tape, press the REWIND Button 4 and
the tape will quickly return.
RECORDING:
RADIO OR TV PROGRAM RECORDING:
1. Set the SELECTOR 11 to the "TV" or "RADIO" position.
2. Set the TV or RADIO BAND SELECTOR 16 or 14 to the desired
position.
3. Adjust the TV TUNING 17 or RADIO TUNING Control 15 to the desired
station.
4. Press the RECORD 3 and PLAY Buttons 6 simultaneously.
EXTERNAL MICROPHONE RECORDING:
1. Insert the microphone plug into the MICrophone Jack 29 and record
following the method above.
2. When using an external microphone with remote control switch
connect the plug to the REMOTE Control Jack 28.
EXTERNAL PROGRAM SOURCE RECORDING:
Connect the external program source to the AUXiliary Jack 30 and
record following the method above.
POSSIBLE CASSETTE RECORDER PLAYING PROBLEM
If Record function doesn't work properly, dirt on the head may be the
cause. Clean it with a head cleaning tape.
(Radio Shack 44-1160) or with a cotton swab lightly moistened with
recommended head cleaning fluid (Radio Shack 44-1170).
EARPHONE (included)
Insert earphone plug into EARphone jack 11 for private listening.
The internal speaker of the unit will be automatically disconnected.
(br/km-07/30/1997)
Privacy Policy