CC-436 RCA CamCorder
(160-0831) Power Faxback Doc. # 37060
Powering the Camcorder
CAUTION: Do not attempt to use a "power converter" to use your AC adapter/
charger on a power source other than 120 volts, 50/60 Hz, or the
adapter/charger and camcorder may be damaged. If you wish to oper-
ate the AC adapter/charger on a power source other than 120 volts,
50/60 Hz, use only a transformer-type power converter. Do not use
"solid-state" or "switching-type" power converters. They will
damage your AC adapter/charger. An optional CPS014 is designed
for use on 100-240 volts, 50/60 Hz.
Using the Adapter/Charger to Power Your Camcorder
1. Connect one end of the adapter/charger's cable to the adapter/charger's
DC OUTPUT jack and the other end to the DC IN 9.6V jack on the back of
the camcorder.
2. Plug the adapter/charger into the nearest AC outlet (120 V, 50/60 Hz).
3. The POWER indicator on the adapter/charger will light when it is proper-
ly connected.
NOTES: The adapter/charger cannot charge the battery and operate the
camcorder at the same time. If you connect both, the adapter/
charger will power the camcorder. Remove the adapter/charger's
cable from the DC OUTPUT jack to charge the battery.
When using the adapter/charger to power the camcorder, the batt-
ery level indicator may display STOP. This indicator is used for
battery operation and has no meaning when using the adapter/
charger to power the camcorder.
To Remove the Adapter/Charger
1. Remove the adapter/charger's plug from the AC outlet.
2. Remove the adapter/charger's DC cable from the DC IN 9.6V jack on the
camcorder.
CAUTION: Do not use this adapter/charger for any purpose other than charg-
ing the EP096FS or EP096FL battery pack or supplying power to the
camcorder.
Using the Battery to Power Your Camcorder
Charging the Battery
The battery must be charged before it can be used the first time. Charging
will take approximately two hours depending on the condition of the battery.
When fully charged, the battery should supply approximately 60 minutes of
operating time (depending on how much you use zoom and pause). To extend
the battery operation time, turn off the camcorder's power when not in use.
1. Attach the battery to the adapter/charger. Align the reference arrow on
the battery with the arrow on the adapter/charger. Hold the battery
flush against the adapter/charger and slide it in the direction of the
arrow.
NOTE: You cannot charge the battery and operate the camcorder from the
adapter/charger at the same time. Remove the adapter/charger DC
cable from the camcorder to charge the battery.
2. Plug the adapter/charger into the nearest AC outlet (120 V, 50/60 Hz).
CAUTION: When a battery is attached to the adapter/charger, do not turn
them upside down. The battery may fall off and be damaged or
cause injury.
3. The CHARGE indicator will light while the battery is being charged.
When the indicator turns off, the battery is fully charged.
4. Remove the battery from the adapter/charger by sliding the battery up
and off.
5. Attach the charged battery to the camcorder as shown on Faxback Doc.
# 37082, Fig. C.
Using the Battery to Power Your Camcorder
Attach Charged Battery
1. Align reference arrow on battery with arrow on camcorder. Hold battery
flush against camcorder while sliding it down in the direction of the
arrow.
2. Press and hold small button on CAMERA/OFF/VCR while placing it in
CAMERA.
Remove the Battery
1. Slide CAMERA/OFF/VCR to OFF.
2. Press and hold BATTERY EJECT while sliding battery up and off the cam-
corder.
ATTENTION: LEAD-ACID BATTERY MUST BE DISPOSED OF PROPERLY. THE PRODUCT THAT
YOU HAVE PURCHASED USES A RECHARGEABLE BATTERY. AT THE END OF
ITS USEFUL LIFE, UNDER VARIOUS STATE AND LOCAL LAWS, IT MAY BE
ILLEGAL TO DISPOSE OF THIS BATTERY INTO THE MUNICIPAL WASTE
STREAM. CHECK WITH YOUR LOCAL SOLID WASTE OFFICIALS FOR DETAILS
IN YOUR AREA FOR RECYCLING OPTIONS OR PROPER DISPOSAL.
Battery Care
Your battery will provide better service and longer performance if you
charge it before and after use, and store it at normal room temperature.
The battery should be charged at a temperature of 32 degrees F - 95
degrees F (0 Degrees C - 35 degrees C) to prevent damage.
Do not operate the battery at temperatures below 14 degrees F (-10
degrees C) or above 95 degrees F (35 degrees C). The battery may be dam-
aged if operated at temperatures above 122 degrees F (50 degrees C).
Operation time will decrease at extremely low temperatures.
After repeated chargings and use, the operation time will gradually de-
crease. When operation time becomes too short to be useful, it is time to
replace the battery.
Battery Storage
Store the battery at normal room temperature.
Lead acid batteries discharge if not used. Recharge the battery at least
once every six months or you may not be able to recharge it.
A battery stored for a long period may not supply power for the specified
time. Additional rechargings may help restore the battery's operation
time.
Battery Safety Precautions
Batteries being recharged that have not been used for an extended period
may continue to charge after the normal time. Do not charge a battery for
more than 24 hours.
If both indicators on the adapter/charger start flashing, remove the batt-
ery, and reattach it. If after several attempts - the indicators continue
to flash - your battery cannot take a charge and must be replaced.
Throwing the battery into a fire or exposing the battery to excessive heat
- over 149 degrees F (65 degrees C) could be hazardous.
Do not short the battery's terminals.
Allow battery to cool down before attaching it to adapter/charger. The
CHARGE indicator will not light and the battery will not charge if you
attach a hot battery.
Do not attempt to disassemble or modify the battery. There are no user-
serviceable parts inside.
Use the battery only with specified AC adapter/chargers and camcorders.
If leakage from a damaged battery contacts your skin or clothing, wash it
off immediately with running water.
Check Battery Power (Battery Level Indicator)
When DISPLAY is pressed, the battery level indicator (SYMBOL) appears in
the camcorder's viewfinder to show how much battery power is left in the
rechargeable battery.
This indicator is not recorded on the tape.
When the battery is fully charged, the display shows (SYMBOL).
After a while, only (SYMBOL) appears.
When the battery reaches the empty level. (SYMBOL) will start flashing.
Recharge the battery or attach the adapter/charger before continuing to
use the camcorder.
NOTES: The battery level indicator has no meaning when you power the cam-
corder with the adapter/charger or optional car cord. When a re-
chargeable battery is used to power the camcorder, (SYMBOL) Flashes
even if DISPLAY is not pressed to warn you that the battery power
level is low.
CAUTION: When the battery reaches its empty level during use, the camcorder
will turn off. However, the battery should have enough reserve
power to eject the cassette when you press STOP/EJECT.
If the camcorder does not eject the cassette when you press STOP/EJECT, do
not force the cassette door open. This will damage your camcorder.
Before attempting to eject the cassette, power your camcorder with the
adapter/charger or recharge the battery.
Using the Optional Thomson Car Cord Adapter
To power your camcorder from the cigarette lighter socket of a car, truck,
or RV, you need the optional car cord adapter DCC096.
The DCC096 car cord is especially designed to convert power from a 12-volt
battery to the 9.6-volt input jack on the camcorder.
CAUTION: The DCC096 car cord is designed to be used only with vehicles
having 12-volt negative ground electrical systems.
WARNING: To avoid possible damage to your camcorder, use only the DCC096.
It has positive tip polarity and is capable of converting 12-volts
to 9.6 volts.
1. Remove the adapter/charger's DC cable or battery from the camcorder,
if either is attached.
2. Connect the small plug on the car cord to the DC IN 9.6V jack located
on the back of the camcorder.
3. Insert the other end of the car cord into the vehicle's cigarette
lighter socket.
4. Place the camcorder's CAMERA/OFF/VCR switch in CAMERA. If the car cord
is connected properly, the electronic viewfinder will come on.
NOTES: The vehicle does not have to be turned on for the camcorder to oper-
ate from the DC car cord.
When using the car cord to power the camcorder, the battery, level
indicator may display STOP. This indicator is used for battery
operation and has no meaning when using the car cord to power the
camcorder.
(BR/EB 10/24/96)
Privacy Policy