Model 30 20" Color TV w/Built-in VHS HQ VCR 160-0422 Setup

Model 30 20" Color TV with Built-in VHS HQ VCR
(160-0422)                 Setup                      Faxback Doc. # 35260

FRONT PANEL

The buttons on the TV/VCR's front panel control the TV and the VCR.

SETTING THE ON-SCREEN LANGUAGE/CHANNELS/CLOCK

The first time you turn on the TV/VCR, the select language screen automatic-
ally appears.  You can set the TV/VCR to display on-screen menus in English
or in Spanish. After you select a language, the TV/VCR automatically scans
through the channels and stores all active channels in your area.  Then the
TV/VCR automatically sets the clock if a broadcast station with an EDS
signal is available in your area.

NOTES:  Make sure you have connected the TV/VCR to your cable system or an
        antenna before continuing (see "Connecting an Outdoor Antenna" or
        "Connecting to a Cable System" on Faxback Doc. # 35259).

        The on-screen language defaults to English.

        EDS is a service provided by some broadcasters to transmit various
        types of information including the current time. If the channels in
        your area do not carry EDS signals, or if you want to use timer re-
        cording immediately, you must set the clock manually after the TV/
        VCR finishes looking for an EDS signal. See "Setting the Clock Man-
        ually" below.

        The TV/VCR might not store active channels and automatically set the
        clock if the signal the TV/VCR receives from your antenna is weak.

1.  Press POWER to turn on the TV/VCR. The SELECT LANGUAGE screen automatic-
    ally appears.

2.  To select the ON-Screen language Press CH /\ to select ENGLISH or CH \/
    to select ESPANOL (Spanish).  The CHANNEL/CLOCK AUTO SET screen auto-
    matically appears.

3.  To automatically scan through the channels in your area and store them,
    then automatically set the clock, press CH /\.

    CH AUTO SET PROCEEDING appears on the screen.

    NOTE:  If you use a cable box, turn it on and select an EDS broadcaster
           in your time zone before pressing CH /\.

    The TV/VCR stores active channels (TV or CATV).

    NOTE:  If the TV/VCR found no active channels during the search, it
           beeps and displays a message on the TV screen.

           Then, it displays AUTO CLOCK SET PROCEEDING, and automatically
           searches for an EDS signal and sets the clock.

Check your antenna or cable connections, then press CH /\ again.

    If the TV/VCR finds an EDS signal during the search, the clock is auto-
    matically set, and a screen shows the currently set date and time.

    If the TV/VCR does not find an EDS signal during the search, you see.

                   AUTO CLOCK SET
                   IS INCOMPLETE

               PUSH MENU TO SET CLOCK

    If this occurs, the broadcaster you selected did not transmit an EDS
    signal, or there is no EDS broadcaster in your area.  Manually set the
    clock (see "Setting the Clock Manually" below).

    If a channel you wanted was not stored, you can add the channel.  If a
    channel you did not want was stored, you can delete the channel.  See
    "Adding/Erasing Channels" below.

    The TV/VCR retains stored channels when you turn off the TV/VCR, or if
    power to the TV/VCR is lost for up to 30 seconds.

Changing the ON-Screen Programming Language

1.  Press MENU on the remote control to display the main menu.

2.  Repeatedly press SEL /\ or SEL \/ on the remote control to select IDIOMA
    (the language selection icon).

    NOTE:  IDIOMA is Spanish for "language."

3.  Press SET on the remote control to change the language.

4.  Repeatedly press SEL /\ or SEL \/ on the remote control to select SALIR,
    then press SET or MENU on the remote control to exit from the menu.

    NOTE:  SALIR is Spanish for "exit."

Changing the Channels Stored in Memory

Although the TV/VCR automatically stores all active channels in your area
the first time you turn it on, you can manually program the tuner's memory.

NOTES:  If you tune both TV (broadcast) and CATV (cable TV) signals you can
        store both types of channels.

        If an EDS broadcaster is available in your area, the TV/VCR also
        automatically updates the clock when you change the channels stored
        in memory.

1.  Press MENU on the remote control to display the main menu.

2.  Repeatedly press SEL /\ or SEL \/ on the remote control to select CH,
    then press SET.  The SET UP CHANNEL menu appears on the TV screen.

3.  If necessary, press SEL /\ or SEL \/ on the remote control to highlight
    ANTENNA SYSTEM, then press SET to display the broadcast system (TV or
    CATV).

4.  Press SEL \/ to highlight AUTO SET then press SET. CH AUTO SET PROCEED-
    ING appears, and the TV/VCR's tuner scans through the channels (TV or
    CATV) and stores all the active channels in your area.  The currently
    tuned channel number appears on the TV screen.  After scanning all the
    channels, CH AUTO SET COMPLETED appears, and the tuner stops on the
    lowest-numbered active channel.

5.  To review the saved channels, repeatedly press CH /\ or CH \/ on the
    remote control.

    NOTE:  You can directly select channels that are not stored in the
           tuner's memory by using the remote control's number buttons. See
           "Selecting Channels" on Faxback Doc. # 35261.

Adding/Erasing Channels

If a channel you want was not stored, or if a channel you do not want was
stored, follow these steps to add or erase it.

1.  Repeatedly press CH /\ or CH \/ or use the number keys on the remote
    control to enter the channel number you want to add or erase.

    NOTES:  You must use the number keys to select a channel that is not
            stored.

            Precede a single-digit number with 0- for example, 01, 02, etc.

2.  Press ADD/DLT on the remote control to add or delete the channel.
    CHANNEL and the CHANNEL number and ADDED or DELETED appears on the TV
    screen.

Setting the Clock Manually

If the TV/VCR did not automatically set the clock, or if there is no EDS
broadcast station your area, you must manually set the clock.  We suggest
you use another TV or a radio station as your time source.

Follow these steps to set the clock manually.

1.  Press MENU to display the main menu.

2.  Repeatedly press SEL /\ or SEL \/ on the remote control to select CLOCK
    then Press SET.  The SET CLOCK screen appears on the TV screen.

3.  Repeatedly press SEL /\ or SEL \/ on the remote control to highlight
    MANUAL SET, then press SET. The next SET CLOCK screen appears on the TV
    screen.

4.  Repeatedly press SET until the month digit flashes.

5.  Repeatedly Press SEL /\ or SEL \/ on the remote control to display the
    correct month, then press SET again.  The day flashes.

6.  Repeat Step 5 to set the day, year, hour, and minute (The TV/VCR auto-
    matically sets the day of the week).

    NOTE:  Your TV/VCR uses a 12-hour clock.  Be sure you set AM or PM
           correctly.

7.  Repeatedly press SEL /\ or SEL \/ on the remote control to turn DST
    (Daylight Saving Time) on or off.

    When DST is set to ON, the TV/VCR automatically adjusts for daylight
    saving time (adds one hour on the first Sunday in April, subtracts one
    hour on the first Sunday in October).

8.  Review the entered information.

    If it is correct, press MENU twice to start the clock.

    If you find an incorrect entry, repeatedly Press SET or CLEAR to move
    back or SEL /\ to move forward to the incorrect number, then enter the
    correct number.  Then press MENU twice.

When you press MENU the seconds begin counting from 00 and the current time
appears on the TV screen.


(BR/EB 10/17/96)