13-Inch Color TV/Monitor
(160-0289) Operation Faxback Doc. # 34436
USING THE TV's CONTROLS
USING THE TV's FRONT PANEL CONTROLS
This section briefly describes the function of each button on the TV's
front panel. Each function is described in detail later in this manual.
FUNCTION - Selects the different on-screen function controls.
VOL - Press the top VOL button to increase the volume and bottom VOL button
to lower it. The number of vertical bars at the lower part of the
screen indicates the relative volume level. You also use these
buttons to adjust the TV's on-screen function controls.
CH - Press the top CH button to select the next higher channel and the
bottom CH button to select the next lower channel. Press and hold down
either button to quickly scroll through channels. See "Using Automatic
and Manual Channel Programming", below.
POWER - Turns on or off the TV.
USING THE REMOTE CONTROL
The remote control has the same controls as the TV's front panel, as well
as the additional controls described in this section.
To operate the remote control, point its front window toward the TV's front
panel. Then press the desired button(s) on the remote control.
Channel Selection (Number) Buttons - Press to directly select a channel.
The selected channel number appears on
the screen for about 5 seconds.
To select a single-digit broadcast (AIR) channel - Channel 5, for example
press 5. You do not need to press 0 before entering a single-digit
channel (but, if you do, the TV changes faster).
To select a double-digit broadcast channel - Channel 12, for example
press 1, and then 2.
To select a three-digit cable channel - Channel 121, for example press 1,
2, and 1.
NOTE: You must select CABLE as the input source before you can select a
cable channel. See "Selecting the Input Signal", below.
RECALL - Displays the current channel number for about 5 seconds. Also
clears the on-screen function displays.
SLEEP - Sets the sleep timer.
PICTURE - Selects a picture control (contrast, brightness, color, tint, or
sharpness) for adjustment.
TV/VIDEO - Selects the TV or VIDEO mode.
CAPTION - Turns the closed caption decoder on or off.
REVIEW - Returns to the previously selected channel.
MUTE - Press once to mute the sound. MUTE appears on the screen. Press
again to restore the sound.
APC (Auto Picture Control) - Returns to the factory preset picture settings
or the settings you select.
SET-UP - Selects the different on-screen function controls. (This button
is similar to the FUNCTION button on the TV; however, it only
performs set-up operations.)
USING AUTO DEMONSTRATION
Auto demonstration lets you see all the on-screen controls.
1. Press SET-UP on the remote control until AUTO DEMO. appears on the
screen.
2. Press VOL + or - to start the demonstration. The screen shows the
different controls and adjusts them so you can see how each one works.
When the demonstration reaches the last display, it starts again from
the beginning.
3. To stop auto demonstration, press any button on the remote control or
front panel. The picture returns to the settings selected before the
demonstration.
OPERATION
TURNING THE TV ON/OFF
Press POWER on the TV's front panel or remote control to turn the TV on or
off.
SETTING THE ON-SCREEN LANGUAGE
1. Press SET-UP on the remote control or FUNCTION on the front panel until
LANGUAGE appears on the screen.
2. Press VOL + or - so the arrow points to ENGLISH or ESPANOL (Spanish).
3. The on-screen display automatically clears in about 5 seconds. Or, you
can press RECALL to clear it.
All on-screen displays are now in the selected language.
SELECTING THE INPUT SIGNAL
Follow these steps to select between receiving cable stations and receiving
broadcast channels.
1. Press SET-UP on the remote control or FUNCTION on the front panel until
INPUT SELECTION appears on the screen.
NOTE: When you press SET-UP on the remote control, VIDEO does not
appear as a selection. Press TV/VIDEO on the remote control to
select VIDEO (see "Selecting TV or Video", below).
2. Press VOL + or - so the arrow points to AIR, CABLE, or VIDEO.
Select AIR if you are using an antenna or CABLE if you are using a
cable service. Select VIDEO to view the audio/video source connected
to the TV's input jacks.
3. The on-screen display automatically clears in about 5 seconds. Or, you
can press RECALL to clear it.
SELECTING TV OR VIDEO
Press TV/VIDEO on the remote control to view the selected input signal (TV)
or the audio/video source connected to the TV's input jacks (VIDEO).
USING AUTOMATIC AND MANUAL CHANNEL PROGRAMMING
When you turn on the TV for the first time, use the automatic channel
programming feature to scan and memorize all active broadcast and cable
channels in your area. If there are additional channels you want to add or
delete, you can manually add or delete them.
Using Automatic Programming
1. Press TV/VIDEO so TV is selected.
2. Press SET-UP on the remote control or FUNCTION on the front panel until
AUTO PROGRAM appears on the screen.
3. Press VOL + or -. The TV automatically scans and memorizes all active
channels in your area.
NOTE: You can press any button on the remote control or front panel to
stop automatic programming.
When the TV has scanned and stored all active channels, it stops
on the nearest programmed channel to where you started.
Now, when you press CH + or -, the TV skips inactive channels.
NOTE: If the TV is unplugged for more than 24 hours, you must repeat
automatic channel programming to restore channels in memory.
Manually Adding a Channel
To add a channel that was not stored during automatic programming, follow
these steps.
1. Press TV/VIDEO so TV is selected.
2. Select the input signal (AIR or CABLE).
3. Use the remote control's number button(s) to select the channel you
want to store.
4. Press SET-UP on the remote control until the channel number, ADD, and
DELETE appear on the screen.
5. Press VOL + and - so the arrow points to ADD.
6. The on-screen display automatically clears in about 5 seconds. Or, you
can press RECALL to clear it. The channel is added.
Manually Deleting a Channel
If the TV stored a channel you do not want, follow these steps to delete
the channel from memory.
1. Press TV/VIDEO so TV is selected.
2. Select the input signal (AIR or CABLE).
3. Press CH + or - or the remote control's number button(s) to select the
channel you want to delete.
4. Press SET-UP on the remote control until the channel number, ADD, and
DELETE appear on the screen.
5. Press VOL + or - so the arrow points to DELETE.
6. The on-screen display automatically clears in about 5 seconds. Or, you
can press RECALL to clear it. The channel is deleted.
AUTO PICTURE CONTROL
Press APC on the remote control to display the Auto Picture Control status.
When PICTURE RESET is set to ON, the TV's picture shows the factory
settings. If you adjust the picture, ON automatically changes to OFF (see
"Adjusting the Picture", below).
If you have adjusted the picture and want to return to the picture controls
you previously selected, press APC until PICTURE RESET OFF appears.
ADJUSTING THE PICTURE
Follow these steps to adjust the picture's contrast, brightness, color
intensity, tint, and sharpness.
1. Press PICTURE on the remote control or FUNCTION on the front panel
until the desired picture control appears.
2. Adjust the selected control level by pressing VOL + or -.
Refer to the following picture control chart.
CONTROL
CONTROL BUTTONS
- +
CONTRAST: ................ Lower ..... Higher
BRIGHTNESS: .............. Darker .... Brighter
COLOR INTENSITY: ......... Lighter ... Deeper
TINT: .................... Reddish ... Greenish
SHARPNESS: ............... Softer .... Sharper
The bar graph on the screen shows the relative adjustment level.
(LB/EB 08/12/96)
Privacy Policy