Model 58 Four Head Hi-Fi Stereo VCR
(160-0628) VCR Setup Faxback Doc. # 18805
SETTING THE VCR'S OUTPUT CHANNEL SWITCH
Set the VCR's OUTPUT CHANNEL switch (on the back of the VCR) to 3 or 4,
whenever is not an active channel in your area.
NOTE: The Model 107's OUTPUT CHANNEL switch looks slightly different than
shown here.
When VCR appears on the display, the VCR sends the signal from the
video source connected to its VHF/UHF CATV OUT terminal to the TV
on the channel you selected.
NOTE: The OUTPUT CHANNEL switch has no effect on the TV when the
VCR is off or if you are using a TV that has separate audio/
video input jacks and that is set to the video mode.
REMOTE CONTROL
Installing the Batteries
The remote control requires two AA batteries (not supplied). For the
longest operation and best performance, we recommend alkaline batteries
(such as Radio Shack Cat. No. 23-557).
CAUTIONS: Use only fresh batteries of the required size and type.
Never leave dead batteries in the remote control.
Dispose of dead batteries promptly and properly; do not bury
or burn them.
1. Press down on the battery compartment cover and slide it in the
direction of the arrow to remove it.
2. Insert fresh batteries into the compartment, as indicated by the
polarity symbols (+ and -) marked inside.
3. Replace the cover.
NOTE: If the remote control does not work or operates poorly, replace
both batteries. If it does not operate properly even after
replacing batteries, remove the batteries once, wait 5 minutes,
then re-install the batteries.
Using the Remote Control
1. POWER
2. EJECT
3. VOL DOWN/UP (for TV only)
4. INSTANT REPLAY
5. PLAY
6. REW/FF
7. STOP
8. REC
9. Number Buttons
10. 100
11. SLOW
12. SLOW/DPSS -/+
13. VCR/TV/CABLE (Mode Selectors)
14. TV/VCR
15. PREV.CH (for TV only)
16. INPUT
17. CH +/-
18. ON SCREEN
19. SKIP SEARCH
20. PAUSE/STILL
21. MODE LOCK
22. TAPE SPEED
23. DISPLAY
24. ZERO BACK
25. CANCEL
26. MENU
To use the remote control, aim its front at the front of the VCR, and
press the desired function buttons.
Setting the Remote Control's Codes
In addition to controlling your VCR, the remote control can operate the
basic functions of 19 different types of TVs and 15 different types of
cable converters (cable boxes).
To use the remote control with your TV and cable box, follow these steps
to program the remote control with the correct two-digit manufacturer's
code number for the TV and cable box.
1. Find the two-digit code for your TV and cable box in the following
chart.
TVs
BRAND CODE
Admiral/Bell & Howell 01, 03, 04
Emerson 18
Fisher 16
Funai 05
GE 06, 08
Goldstar 17
Hitachi 14
JVC 15
Magnavox 08, 10
Mitsubishi 13
Panasonic 12
RCA 06, 08
Samsung 19
Sanyo 16
Sharp 01, 02
Signature 2000 01, 03, 04
Sony 09
Toshiba 11
Zenith 04, 07
Jerrold 1 01
Jarrold 2 02
Jarrold 3 03
Jarrold 4 04
Jarrold 5 05
Jerrold 6 06
Jerrold 7 07
Panasonic 13
Pioneer 1 14
Pioneer 2 15
RCA 13
Regal 1 10
Regal 2 11
Scientific Atlanta 1 06
Scientific Atlanta 2 09
Zenith 12
NOTE: Some brands of TVs and cable boxes have more than one code
listed in the charts above. If a code does not work with
your TV or cable box, try another code.
2. Press TV and CH positive on the remote control at the same time.
3. Within 10 seconds, use the number keys to enter the code for your
TV. Precede a single-digit code with 0 - for example, 01, 02, etc.
4. Press CABLE and CH positive on the remote control at the same time.
5. Within 10 seconds, use the number keys to enter the code for your
cable box. Precede a single-digit code with 0 - for example, 01,
02, etc.
NOTE: If you do not enter the code for your TV or cable box within
10 seconds, the remote control does not save the code. Simply
start again from Step 2 or Step 4.
The remote control will not operate some TVs and cable boxes.
If this happens, you must use the original remote control
supplied with your TV or cable box.
The codes you programmed might be erased if you remove the
batteries from the remote control. If the codes were erased,
re-enter the codes after you replace the batteries.
Your TV might have functions that the remote control will
not operate.
To operate the VCR, TV, or cable box with the remote control, press the
corresponding button (VCR, TV, or CABLE) to switch to the desired device,
than press the desired function button.
SETTING THE ON-SCREEN PROGRAMMING LANGUAGE
Use the remote control to select the language you want the VCR to display.
NOTE: The on-screen programming language defaults to English.
1. If necessary, press POWER until --:-- disappears. SP (the tape
speed), L and R (if you have a Model 58), and CH and the current
channel number appear on the VCR's display.
2. Turn on your TV and set it to the same channel as the OUTPUT CHANNEL
switch located on the back of the VCR.
NOTE: If you are using a TV/monitor that is connected to the VCR's
AUDIO/VIDEO OUT jacks, set it to the video mode.
3. Repeatedly press TV/VCR until VCR appears on the VCR's display.
4. Press MENU on the remote control select the main menu display. The
menu display appears on the TV screen. If a menu is not displayed,
you can also press SET UP on the VCR to display the setup menu.
NOTE: If you have not yet selected a language, the language setting
menu automatically appears on the TV screen. Proceed to
Step 6.
5. Press 4 on the remote control to select the language setting menu.
The menu appears on the TV screen.
6. To select the on-screen programming language, press 1 to select
ENGLISH, 2 to select ESPANOL (Spanish), or 3 to select FRANCAIS
(French). The language you selected is highlighted.
7. Either wait 1 minute or press MENU. The language setting menu
disappears, and you see --:-- on the VCR's display. Set the VCR's
clock. (See "Setting the Clock").
SETTING THE CLOCK
NOTE: Your VCR has a special memory sentinel feature that protects clock
settings, tuner programming information, and timer memory settings
for up to 1 hour in case a power failure occurs or the power cord
is unplugged. After about 1 hour without power, the VCR loses all
clock, tuner, and memory settings.
1. Press MENU on the remote control to select the main menu display.
The menu display appears on the TV screen.
2. Press 3 on the remote control to select CLOCK. The clock set menu
appears on the TV screen. MONTH is highlighted, and the first digit
of the currently set month (or --) flashes.
3. Use the number keys on the remote control to enter the correct month,
day, and year. For example, to set February 15, 1996, press 0, 2, 1,
5, 9, and 6.
NOTES: Precede a single-digit number with a 0-for example, 01, 02,
etc.
If you enter an incorrect number, repeatedly press CH positive
and negative to move the flashing box to the incorrect number,
then enter the correct number.
4. Use the number keys on the remote control to enter the correct hour
and minute. For example, to set 10:28, press 1, 0, 2, and 8.
5. Press 1 if the hour is an AM hour or 2 if the hour is a PM hour.
D. S. T. is highlighted.
6. To set daylight saving time (DST), press 1 (ON) or 2 (OFF).
When D.S.T. is set to ON, the VCR automatically adds one hour to all
displayed times on the first Sunday in April, and subtracts one hour
from all displayed times on the last Sunday in October.
7. Review the entered information.
If it is not correct, repeatedly press CH positive or negative to
move the cursor to the incorrect information, then enter the correct
information.
If it is correct, either wait 1 minute or press MENU. The screen
disappears.
NOTE: If you enter an invalid date or time (for example , 13:00 for the
time), that entry flashes when you press MENU. Re-enter the
correct date or time.
SELECTING THE INPUT/OUTPUT SIGNAL
Depending on the type of broadcast signals you receive, you must select
the input signal (the source you want the VCR to tune).
If You Are Using an Antenna Only
If you connected an antenna (not cable) to the VCR and want to receive up
to 68 VHF/UHF channels, you must select TV from the TV/CATV menu.
1. Turn on your TV and VCR.
2. Press MENU on the remote control to select the main menu display.
The menu display appears on the TV screen.
3. Press 2 on the remote control to select SETUP. TV/CATV is highlighted,
and the currently selected option (TV, CATV-STD, CATV-HRC, or
CATV-IRC) flashes on the TV screen.
4. If necessary repeatedly press CH positive or positive until TV
flashes on the TV screen.
5. Either wait 1 minute or press MENU. The setup menu disappears.
If You Have Cable
If you have cable service and use a cable box, you must select TV from
the TV/CATV menu.
If you have cable service and do not use a cable box, you must
select one of the CATV settings (STD, HRC, or IRC) from the TV/CATV
menu, depending on your type of cable service.
NOTE: Most cable systems use STD, but if you are not sure what type of
cable service you have, contact your cable company.
Follow these steps to select the input and output signal.
1. Turn on your TV and VCR.
2. Press MENU on the remote control to select the main menu display.
The menu display appears on the TV screen.
3. Press 2 on the remote control to select SETUP. TV/CATV is highlighted,
and the currently selected option (TV, CATV-STD, CATV-HRC, or CATV-
IRC) flashes on the TV screen.
4. If you are a cable box, repeatedly press CH positive or negative
until TV flashes on the TV screen.
If you do not use a cable box, repeatedly press CH positive or
negative until the option you want (CATV-STD, CATV-HRC, or CATV-IRC)
flashes on the TV screen.
NOTE: CATV appears on the VCR's display if you select CATV-STD, CATV-
HRC, or CATV-IRC.
5. Either wait 1 minute or press MENU. The setup menu disappears.
SETTING THE CHANNELS YOUR VCR CAN TUNE
You can program the tuner's memory so the VCR tunes only the active
channels in your area.
1. From the main menu display, press 2 on the remote control or to select
SET UP. The setup menu appears on the TV screen.
2. Press 2 on the remote control to select AUTO CH SET. AUTO CH SET
is highlighted.
3. Press CH positive or negative. The VCR's tuner scans through the
channels (TV or CATV) and memorizes all the active channels in your
area. AUTO SET appears on the TV screen, and the current channel
number appears on the TV screen and the VCR's display. After scanning
all the channels, the tuner stops on the lowest-numbered active
channel.
4. Repeatedly press CH positive or negative to review the channels you
stored.
Adding/Erasing Channels
If a channel you want did not get automatically memorized, or if a channel
you do not want did get memorized, follow these steps to add or erase a
channel.
1. Use the number keys on the remote control to enter the channel number
you want to add or erase.
NOTE: Precede a single-digit number with a 0 - for example, 01, 02,
etc.
2. From the main menu display, press 2 on the remote control to select
SET UP. The setup menu appears on the TV screen.
3. Press 4 on the remote control to select ADD/ERASE. ADD/ERASE is
highlighted.
4. Press CH positive. The channel number you entered in Step 1
displayed.
5. Press CH positive to add the channel or CH negative to erase the
channel.
If you press CH positive, ADD briefly appears on the screen and
AD appears on the VCR display.
If you press CH negative, ERASE briefly appears on the screen and
ER appears on the VCR's display.
6. Either wait 1 minute or press MENU. The ADD/ERASE screen disappears.
7. Repeat Steps 1 - 6 to add or erase another channel.
Privacy Policy