CP 1700  (170-1016)             Operation              Faxback Doc. # 9628

Placing, Receiving, and Ending Calls

You may place a call manually, by using the redial function, or by
recalling a number from the memory.

NOTE:  For best call quality, keep the antenna free from obstructions and
       pointed straight up.

Manually Place a Call

You can enter your number with the handset off or on the cradle.  Use the
numeric keypad as you would for any push-button phone and press SEND.

As you enter each digit, the number appears on the LCD.

The LCD displays only 10 digits at a time.  As you enter more digits, the
phone number shifts off the left side of the LCD.

To view the numbers that have shifted off the LCD to the left, Press RCL
<*.

To view the numbers that have shifted off the LCD to the right, Press RCL
#>.

Make Corrections

Press CLR to erase the last digit entered.  To erase additional digits,
press CLR repeatedly.

To erase the entire number, Press and Hold CLR until the beep ends (in
about a second) or Press RCL CLR.

Redial Last Number Called

The last number called is stored in memory.  To redial the number, Press
SEND.  To display the number before redialing, Press RCL 0 0.

Use Memory to Place a Call

To place a call using a number stored in memory:

1.  Press RCL and the two digit code for the memory location (e.g. 1 0). 
    The stored number is displayed on the LCD.

2.  Press SEND.

    NOTE:  If a pause has been programmed in the stored number, the CP
           1700 dials only up to the pause, and then stops.  To continue
           dialing, Press SEND again.  (See the "Program a Pause"
           section.)

3.  To end the call hand up, or Press END.

Receiving a Call

When you receive an incoming call, you hear the Alert Tone and CALL-#
appears on the LCD.

To answer the call, pickup the handset and begin your conversation.  If
the handset is already off the cradle, Press SEND.

Placing a Call On Hold

During a call, Press RCL 6 6, and place the Handset on the cradle.  You
can still hear the caller through the Monitor Speaker.  Lift the Handset
to return to the call.

End a Call

To end a call, place the Handset on the cradle, or Press SEND.

30 NUMBER MEMORY STORAGE

You can have up to 32 digits in any of the 30 memory locations (01-30).

Enter a number into memory:

1.  Press and Hold CLR at least 0.6 seconds to clear the display.

2.  Enter the digits (phone number, credit card number, etc.) to store.

3.  Press STO.

4.  Enter the two digit memory location number (01-30).

    NOTE:  You must enter two digits (e.g. 0 1).

5.  After the second number is pressed, the display blinks twice.

    NOTE:  Any number previously stored in that location is erased when
           the new number is stored.

Program a Pause

Use this when two numbers are dialed one after another, such as access
codes.  To program a pause within a numeric sequence, press END.

A P is displayed between the numbers to indicate a pause has been
programmed.

To CP 1700 recognizes only one pause in a sequence of numbers.

Display Memory Numbers

Press RCL and the 2 digit memory location number (01-30).

Example:  To display the number stored in memory location 10, press RCL 1
          0.  The display will show the lower seven digits of the number. 
          If you need to display more of the number (such as the area
          code), Press RCL again.  The 2 digit memory location number will
          be replace by the remainder of the stored number.  If necessary,
          Press /\ or \/ to scroll up or down to display additional memory
          locations.

Erase a Memory Number

To completely erase a number store din one of the memory locations, Press
CLR, then Press STO and the two digit memory number.  Always use two
digits, e.g. 0 6.

VOLUME ADJUSTMENTS

Handset Earpiece Volume

In standby, Press RCL 7 5 2 to adjust the Earpiece Volume for the handset
in seven levels.

The display shows the level as you set it.

You can also adjust the Handset Earpiece volume during a call by pressing
\/ or /\.

Alert Volume

In Standby, Press RCL 7 5 1 /\ \/ to adjust the Alert Volume from the
cradle in three levels.

The display shows the level as you set it.

Monitor Speaker Volume

In Standby, press RCL 7 5 3 to adjust the monitor Speaker Volume in seven
levels.

You can also adjust the speaker volume while a call is on hold by pressing
\/ or /\.

Keypad Tone Volume

In Standby, press RCL 7 5 4 and \/ or /\ to adjust the Keypad Tone Volume
in 5 levels.

System Selection

     1.  Press RCL 88 to recall the selected system.

     2.  Find the number of the system that you wish to select.

     3.  Press the number (1-5) and 'STO' 88.

(ALL/ir-07/12/95)

Privacy Policy