Cellular Mobile Telephone
CT-105/1050/1055 (170-1079/1021/1007) NAM Programming Faxback Doc. # 8728
NOTE: Some of the above Cellular Mobile Telephones will use the [STOR] key
while others will use the [*] key. Substitute the appropriate key
for your particular cell phone. (i.e.; If your phone does not have
the [STOR] key then use the [*] key where ever it is called for in
the programming procedure.)
General Details
The Number Assignment Modules (Pozidrive) are programmed using the handset
in the Cellular Telephone. The procedure should only be carried out by an
Authorized Distributor. As each (Numbered) instruction of this procedure
is completed the display will show a message, similar to that illustrated
beneath each instruction which will act as a prompt for the next action.
NOTES: 1. Certain values shown in the display examples are typical and the
actual values displayed on the telephone may differ.
2. If at any time during NAM Programming an incorrect character is
selected, it may be rectified by pressing the CLR key and then
selecting the required character.
Default NAM Settings
Description Phone Display Setting
___________ _____________ _______
Local Operator Number OPR. NO ? 611
Own Number Displayed at switch on NUM ? Uses 'MIN'
(or when requested from menu) setting
Local Emergency Service Number EMERGENCY NO ? 911
Outgoing International Call Code INTERNAT CODE ? 011
Overload Class Mark O/LOAD CLASS 00 Least significant
digit of 'MIN'
Extended Addressing Mode EXP ? 0 01
Initial Home Paging Channel IPCH ? 0000 333 or 334
Depending on CID
Preferred Initial Home Paging PREF ICC 0000 IPCH
Channel
Non Preferred Initial Home Paging NON-PREF ICC 333 (if IPCH=334)
Channel 0000 334 (if IPCH=333)
Procedure
Press the PWR key to switch ON the Cellular Telephone and enter the NAM
programming:
To Enter Program Mode Type:
# 000000 ## 953739 # <SEL> <*> 49 <SEL> <SEL>
Phone Responds: Memory 49 Stored
Press <PWR> to turn the phone off, then on again.
Phone Responds: WHICH NAM?
Press 1 then <SEL> to select the first NAM.
*Line 1 of Phone: SYST.ID Type: 5-digit Home System ID then <SEL>
Line 1 of Phone: No. Type: 10-digit Cellular Phone # <SEL>
*Line 1 of Phone: GROUP ID Type: 2-digit carrier Group ID then <SEL>
Phone Responds: SAVE NAM? Press <SND> 1 <END> to save the
programming, which will fill in the
remaining options and exit. Press
<SEL> to modify the remaining
parameters.
Line 1 of Phone: OPR. NO Type: Normally *611 then <SEL>
Line 1 of Phone: NUM Type: Optional # that will be displayed on
power up, then <SEL>
Line 1 of Phone: NAM ID Type: Optional abbreviation for carrier
city, then <SEL>
Line 1 of Phone: EMERGENCY NO Type: Normally 911 then <SEL>
Line 1 of Phone: INTERNAT CODE Type: Normally 011 then <SEL>
Line 1 of Phone: O/LOAD CLASS Type: Normally 0 and last digit of phone #,
then <SEL>
Line 1 of Phone: EXP Type: 1 then <SEL>
Line 1 of Phone: IPCH Type: Initial Paging Channel: 0333 if
paging chan A, or 0334 if paging
chan B, then <SEL>.
Line 1 of Phone: PREF ICC Type: Preferred Paging Channel: 0333 if
paging chan A, or 0334 if paging
chan B, then <SEL>.
Line 1 of Phone: NON-PREF ICC Type: Non-Pref Paging Channel, should be
opposite PREF ICC
Phone Responds: SAVE NAM? Press <SND> 1 <END> to save the
programming.
Settings List: (<SEL> to select options, then press <END> to save)
MENU A: MENU B:
<SEL> 0 Phone Lock <SEL> <SEL> 0 Horn Alert
<SEL> 1 Go to menu B <SEL> <SEL> 1 Go To Menu C
<SEL> 2 Alpha (Name) Search <SEL> <SEL> 2 Backlight Timer
<SEL> 3 Display/Select Phone # <SEL> <SEL> 3 Message Language
<SEL> 4 System Type <SEL> <SEL> 4 Datalink Select
<SEL> 5 Last call Timer <SEL> <SEL> 5 Touch Tone Options
<SEL> 6 Timed Auto Redial <SEL> <SEL> 6 Battery Saver
<SEL> 7 Alarm Timer
<SEL> 8 Key Entry Volume
<SEL> 9 Ringing Volume
MENU C:
<SEL> <SEL> <SEL> (Security Code) 0 Display Own Serial Number (ESN)
<SEL> <SEL> <SEL> (Security Code) 1 **Memory Calls (1-20) Only
<SEL> <SEL> <SEL> (Security Code) 2 Change Security Code
<SEL> <SEL> <SEL> (Security Code) 3 Erase All Memory
<SEL> <SEL> <SEL> (Security Code) 4 **Memory Lock
<SEL> <SEL> <SEL> (Security Code) 5 Display/Reset Airtime Meter
<SEL> <SEL> <SEL> (Security Code) 6 Service Mode
NOTES: **These are the most likely to cause programming/use errors.
Security and Pin codes are the same (factory default 0000).
(PN/jej-04/07/95)
(EB 2/4/98)
Privacy Policy