ET-475  (430-0572B)           Installation             Faxback Doc. # 7326

READ THIS BEFORE INSTALLATION

We have designed your telephone to conform to federal regulations, and you
can connect it to most telephone lines.  However, each device that you
connect to the phone line draws power from the phone line.  We refer to
this power draw as the device's ringer equivalence number, or REN.  The
REN is shown on the bottom of the phone.

If you are using more than one phone or other device on the line, add up
all the RENs.  If the total is more than five, the phones might not ring.
In rural areas, a total REN of three might impair ringer operation.

FCC STATEMENT

This telephone complies with Part 68 of FCC Rules.  You must, upon
request, provide the FCC Registration Number and the REN to the phone
company.  These numbers are located on the bottom of the phone.

Note:  You must not connect the phone to any of the following:

       Coin-operated systems

       Party-line systems

       Most electronic key phone systems

SELECTING A LOCATION

You can mount the base on a wall plate, mount it directly on the wall, or
place it on a desk, shelf, or table.  Select a location that meets the
following requirements:

       Near an AC outlet

       Near a telephone line jack

       Out of the way of normal activities in the area

       Away from electrical machinery, electrical appliances, and metal
       walls or filing cabinets

       Away from wireless intercoms, alarms, and room monitors.

The base's location affects the phone's range.  If you have a choice of
several locations, try each location to see which one provides the best
performance.

If the phone line jack is not a modular jack, you must update the wiring.
You can convert the wiring yourself, using jacks and adapters available at
your local Radio Shack store.  Or, you can let the phone company update
the wiring for you.

The phone company will charge you for the installation of the necessary
jacks.  The phone company will ask you for the USOC number of the jack to
be installed.  This number is RJ11C for a baseboard jack and RJK11W for a
wall-plate jack.

MOUNTING THE BASE

Once you select a location for the base, follow the appropriate mounting
instructions.

On a Desk Top

Follow these steps if you place the base on a desk, shelf, or table.

1.  Plug one end of the supplied modular cord into the PHONE jack on the
    bottom of the base.

2.  Plug the modular cord's other end into a modular phone line jack.

3.  Insert the supplied AC adapter's barrel plug into the DC 12V jack on
    the bottom of the base.

4.  Plug the adapter into a standard AC outlet.

On a Wall Plate

Follow these steps to mount the base on a standard wall plate.  This
requires a short modular cord (Cat. No. 279-390).  The required cord and a
selection of wall plates are available at your local Radio Shack store.

1.  Plug one end of the short modular cord into the PHONE jack on the
    bottom of the base.  Plug the other end into the wall plate's jack.

2.  Insert the supplied AC adapter's barrel plug into the DC 12V jack
    on the bottom of the base.  Then, route the adapter's cord through the
    right-hand clips on the bottom of the base and plug the adapter into a
    standard AC outlet.

3.  Align the base's keyhole slots with the wall plate studs and slide the
    base downward to secure it.

4.  Lift and rotate the handset holder so that it can hold the handset in
    place.

Directly on the Wall

Follow these steps to mount the base directly on the wall.  This requires
two screws (not supplied).

1.  Drill two holes 3 15/16 inches apart.  Then, thread a screw into each
    hole, letting the head extend 1/4 inch from the wall.

2.  Plug one end of the supplied modular cord into the PHONE jack on the
    bottom of the base.

3.  Route the cord downward and under a pair of clips.  Then, plug the
    cord's other end into a modular phone line jack.

4.  Insert the supplied AC adapter's barrel plug into the DC 12V jack on
    the bottom of the base.  Then, route the adapter's cord through the
    other pair of clips on the bottom of the base and plug the adapter
    into a standard AC outlet.

5.  Align the keyhole slots with the mounting screws and slide the base
    downward to secure it.

6.  Lift and rotate the handset holder so that it can hold the handset in
    place.

(br/all-8/11/94)

Privacy Policy