ET-910 900 MHz Digital Cordless Speakerphone w/Dual Keypads
(430-1085A)                Installation               Faxback Doc. # 58094

Selecting A Location

You can set the ET-910's base on a flat surface (such as a desktop or 
countertop), mount it on a modular jack wall plate, or mount it directly 
on the wall.  The base's location affects the phone's range.  If you have 
a choice of several locations, try each to see which one provides the best 
performance.

Select a location that is:

  Near an AC outlet.
  
  Near a telephone line jack.

  Away from electrical machinery, electrical appliances, and metal walls
  or filing cabinets.

  Away from wireless intercoms, alarms, and room monitors.

If the phone line jack is not a modular jack, you must update the wiring.
You can convert the wiring yourself, using jacks and adapters available at 
your local RadioShack store.  Or, you can let the phone company update the 
wiring for you.

Notes:  The phone company charges for the installation of the necessary
        jacks.

        The USOC number of the baseboard jack to be installed is RJ11C.

        After you mount the phone, you must install the battery pack and
        charge it for 24 hours before you use it the first time.  See
        "Preparation" in Faxback Doc. # 58095.

Placing The Base On A Desktop

1.  Plug one end of the supplied 7-foot modular cord into the TO TEL LINE
    jack on the back of the ET-910's base.

2.  Plug the modular cord's other end into a modular phone line jack.

3.  Plug the ET-910's AC cord into a standard AC outlet.

4.  For the best reception, adjust the base's antenna so it stands
    straight up.

Mounting The Base On A Wall

Using the supplied mounting bracket, you can mount the ET-910's base on a 
phone jack wall plate or directly on the wall.

To prepare the bracket for mounting, twist off the tabs attached to the 
center of the bracket and press them securely into the holes on the narrow 
end of the bracket.

Mounting on a Wall Plate

1.  Press the ET-910's AC cord under the recessed clip directly below it
    on the bottom if the phone.

2.  Plug one end of the supplied 7-inch modular cord into the TO TEL LINE
    jack, then press the cord under the other recessed clip on the bottom
    of the phone.

3.  Insert the tabs on the supplied mounting bracket into the slots on the
    base's bottom.  Then press the bracket down until it snaps into place.

4.  Press the AC cord into the top and bottom grooves on the left side of
    the bracket, press the modular cord into the center groove on the
    right side of the bracket, then plug the modular cord into the modular
    phone jack.

5.  Line up the keyhole slots on the bracket with the studs on the wall
    plate, then slide the base down onto the wall plate until it is secure

6.  Press up on the handset holder to remove it, turn it over so its
    tabbed edge faces up, then press it back down into its slot on the
    base.

7.  Plug the ET-910's AC cord into a standard AC outlet.

8.  For the best reception, adjust the base's antenna so it stands
    straight up.

Note:  If you want to remove the supplied bracket after attaching it,
       simply press in the tab on each side of the bracket and lift the
       bracket away from the base.

Mounting Directly on the Wall

Using a drill (not supplied) and the supplied screws and spacers, you can 
easily mount your ET-910 directly on the wall.

1.  At the desired mounting location, drill two holes 3-15/16 inches
    apart, one above the other.

2.  Place a spacer over each screw, then thread a screw into each wall
    hole until the screw's head extends about 1/4 inch from the wall.

3.  Press the ET-910's AC cord under the recessed clip directly below it
    on the bottom of the phone.

4.  Plug one end of the supplied 7-foot modular cord into the TO TEL LINE
    jack, then press the cord under the other recessed clip on the bottom
    of the phone.

5.  Insert the tabs on the supplied mounting bracket into the slots on the
    base's bottom, then press the bracket down until it snaps into place.

6.  Press the AC cord into the top and bottom grooves on the left side of
    the bracket, press the modular cord into the top and bottom grooves on
    the right side of the bracket, then plug the modular cord into a
    modular phone jack.

7.  Line up the keyhole slots on the bracket with the screws on the wall,
    then slide the base down onto the screws until it is secure.

8.  Press up on the handset holder to remove it, turn it over so its
    tabbed edge faces up, then press it back down into its slot on the
    base.

9.  Plug the ET-910's AC cord into a standard AC outlet.

10. For the best reception, adjust the base's antenna so it stands
    straight up.

Note:  If you want to remove the supplied bracket after attaching it,
       simply press in the tab on each side of the bracket and lift the
       bracket away from the base.

(LB EB 12/28/99)