MVX-480/480-XL/485 Audiovox Cellular Phone
(170-1256) NAM Programming Faxback Doc. # 57561
If the unit is new, (Never Programmed), the NAM entry code is
[0][0][0][FUNC][#][8][1].
If already programmed with an unlock code, unlock the phone, then enter
[UNLOCK CODE][FUNC][#][8][1].
If already programmed with a NAM PROGRAMMING CODE, then enter [PROGRAMMING
CODE][FUNC][#][8][1].
If the phone has been pre-programmed including an ACTIVATION CODE, the 7
digit activation code MUST be entered first. The phone will remain
unusable (the word "code?" will be displayed) until the 7 digit code is
entered.
Programming Sequence
ITEM DESCRIPTION ENTRY (# of digits) PRESS
01 AREA CODE XXX [VOL]
02 3 DIGIT PREFIX XXX [VOL]
03 4 DIGIT SUFFIX XXXX [VOL]
04 LOCK CODE XXX [VOL]
05 HOME AREA SYSTEM ID (SID) XXXXX [VOL]
06 ACCESS OVERLOAD CLASS XX (00-10) [VOL]
07 GROUP ID MARK XX [VOL]
08 LOCAL USE MARK X (0 or 1) [VOL]
09 MIN MARK X (0 or 1) [VOL]
10 INITIAL PAGING CHANNEL XXXX (0333 or 0334) [VOL]
11 PREFERRED SYSTEM MARK X (0 = B)(1 = A) [VOL]
12 STATION CLASS MARK (do not change) XXXX [VOL]
Note: Press [FUNC] then [SND].
Wait for "Checksum Adjust" to Display.
Press [FUNC], [CLR].
13 FUNCTION MARK # 1 XXXXX [VOL]
Note: 10000 Activates Auto Cell-Site Redial)
01000 Activates Outgoing Call Timer)
00000 RESERVED
00000 RESERVED
00000 RESERVED
14 RESERVED [#]
15 RESERVED [#]
16 RESERVED [#]
17 CALL TIMER RESET CODE XXX [VOL]
Note: ITEM 18 through 67 are the same as # 18 below with SID MANAGEMENT
# 01 through SID MANAGEMENT # 50.
18-67 SID MANAGEMENT # 01-50 XXXXX [VOL]
68 RESERVED [#]
69 RESERVED [#]
70 RESERVED (1) [#]
71 ACTIVATION CODE XXXXXXX [VOL]
72 CHECKSUM ADJUST (SET BASED ON 1 - 71, 73)
73 CHECKSUM (AUTOMATICALLY SET (80 H)
Press [FUNC][SND] to write the new data into the NAM; WAIT for the
CHECKSUM ADJUST to be displayed (72 XX), then press [FUNC][CLR] to exit
the programming mode.
To increment item numbers, press [#], to decrement press [*]. To jump
forward or backward to an item, press [RCL][ITEM NUMBER]. To change an
entry, enter the new information and press [STO]. After entering all the
new information, press [FUNC][SND] then press [FUNC][CLR]. It is NOT
necessary to jump to the end of programming first.
If the programming mode was entered to check locations (no new information
was entered, or the [STO] key has not been pressed), it is not necessary
to press [FUNC][SND]. [FUNC][CLR] by itself will exit the programming
mode.
A-KEY
To program the A-KEY, enter [2][5][3][9][FUNC][FUNC]. Enter the 20 digit
A-KEY followed by the 6 digit checksum. Then press [STO][STO]. If
"invalid" is displayed; either ESN, A-KEY (with checksum) or MIN do not
agree. If "valid" is displayed, press [END] to exit.
When using Multi-city registration, only 3 AUTHENTICATION GROUPS (mobile
phone number, A-KEY with checksum, ESN and SSD update info) can be entered
Each of the 3 authentication groups are stored as a complete set so the
phone number will be matched with the proper A-KEY etc. Only 3 registered
phone numbers are supported for authentication. Any registered numbers
beyond these 3 can only be used in non-authenticated systems.
A-KEY's (with checksum), SSD info, and so on, are provided by the CARRIER.
(EB 11/19/99)
Privacy Policy