Nokia 918 Series Cellular Telephone
(170-1242/1222) Directory Faxback Doc. # 48280
Your phone can store:
up to 40 names and numbers in its directory.
one additional number in a "notepad", which is erased whenever you
switch off the phone.
the last five numbers you've dialed.
Memory Location Number of Characters Number of Digits
1 16 32
2-21 16 16
22-40 16 32
See "Memory Location 40" below for an important note about Memory Location
40.
Note: If you try to store a digit string greater than 16 characters in a
short memory location (locations 2-21), the message DIGITS MAX = 16
is briefly displayed and the phone exits the store function. The
string you tried to store will reappear on the display and you can
store it in a long memory location.
Alpha Mode
To enter names, retrieve numbers based on names, and view names, press
[ABC]. The phone displays ABC to indicate that you can use keys to enter
letters, and that you are viewing names rather than numbers.
When a name is displayed you can also press [ABC] to see the associated
number.
To Enter Letters
Put the phone in Alpha mode by pressing [ABC]. You can then enter
letters. The table below shows the characters you can enter while the
phone is in Alpha mode.
To correct mistakes, press [CLR] or press and hold [CLR] to clear the
whole display.
KEY One press Two presses Three presses Four presses
1 - & . :
2 A B C
3 D E F
4 G H I
5 J K L
6 M N O
7 P Q R S
8 T U V
9 W X Y Z
* Enter another letter from the same key without waiting for the
cursor to move to the next space.
# Space between letters
The identical name may be used only once in memory. REPLACE NAME? appears
when you try to store a name already in memory.
To Store Numbers and Names
Quick Store
1. Clear the display, then enter the area code and phone number.
2. (Optional:) Press [ABC] then enter the name.
3. Press and hold [OK].
The phone stores the number in the first empty memory location. If
there aren't any empty spaces you get the message NO SPACE.
Menu Method
1. Press [MENU] [\/] [OK]. The phone prompts you for a name.
2. Enter a name then press [OK]. If you don't want to store a name, just
press [OK] at the prompt.
The phone prompts you for a number.
3. Enter the area code and phone number then [OK].
The phone prompts you to store the number in the first available
memory location.
4. Press [OK] or enter the location number where you want the number to
be stored then press [OK].
Note: To store the number in the "Notepad", press [#] at the "STORE TO
n?" prompt then press [OK].
Notes about Storing Numbers
REPLACE NAME?
This appears if the name is already in use.
The phone displays the number (in the upper right hand corner) of the
location where it is stored. To replace the information already stored,
press [OK].
STORE TO?
This appears if there is no empty location available. Enter the memory
location where you want to store the information (existing content will be
overwritten; see next paragraph). Enter a location number and press [OK].
REPLACE CONTENT?
This prompts you to replace the contents of the selected location. To
replace the information, press [OK].
ALREADY STORED
This appears if both the phone number and name are already stored. The
phone prompts you to move the information to the first empty memory
location (e.g., MOVE TO 5?). Press [OK], or enter a different location
number then press [OK].
Press [CLR] if STORE, REPLACE or MOVE appears and you do not want to
continue.
The phone exits the store function, and the information you tried to store
reappears on the display. You can attempt to store the information in the
phone directory memory as described above, or you can clear the display by
pressing and holding [CLR].
To Change the Number Stored with a Name
1. Recall the number from memory.
2. Use the [CLR] key to erase the current number one digit at a time,
then key in the new number.
3. Press and hold [OK]. The phone gives you the prompt "REPLACE NAME?".
4. Press [OK] at the REPLACE NAME? prompt.
Memory Location 40
Memory Location 40 is special. If you store a number in Memory Location
40 (you would do this in Step 4 of "Menu Method" above), you can make
calls to that number even if you turn on the INCOMING ONLY restriction
under Menu 4, Restrict Calls. See "Menu 4, Restrict Calls" in Faxback
Doc. # 48281.
To Erase Stored Names and Numbers
To Erase by Name
1. Press [MENU] [\/\/\/] [OK]. The phone prompts you for a name:
2. Press [\/] until you see the name you want to erase. At the ERASE?
prompt, either press [OK] to erase or press [CLR] if you change your
mind and don't want to erase and you want to quit.
The phone displays ERASED or NOT ERASED.
To Erase by Number
1. Press [MENU] [\/\/\/] [OK]. The phone prompts you for a name, as in
Step 1 above.
2. Press [ABC], and the phone asks you for a location.
3. Press [\/] until you see the number you want to erase, or enter a
location number. At the ERASE? prompt, press [OK] or press [CLR] if
you change your mind.
The phone displays ERASED or NOT ERASED.
Note: The notepad memory is automatically ERASED when you switch the
phone off.
To Recall Stored Numbers
With the display clear of numbers, press [\/].
The phone scrolls through stored numbers.
To Recall Stored Names
With the display clear of numbers or names, press [ABC] then [\/]. Or,
press [ABC] then enter the first few letters of the name and press [\/].
The phone scrolls through stored names.
You can also use Menu 2, Find Name:
1. Press [MENU] [\/\/] [OK]. The phone prompts you for a name:
2. Key in the name or its first letter(s), or press [\/] until you see
the name you want. if you don't enter anything for 5 seconds after
NAME? displays, the first stored name will appear. Press [ABC] to
display the phone number.
3. Press [SEND] to make a call to the displayed name or phone number.
Dialed Calls Memory
The phone automatically stores the five last dialed numbers. A phone
number cannot be stored twice in the list.
When you dial a number that already exists in the list, the dialed number
is moved to the top.
See "Last 5 Dialed Numbers" in Faxback Doc. # 48279 for information on
accessing the last 5 dialed numbers.
To Erase The Last 5 Dialed Numbers
1. Press [MENU] [\/\/\/] [OK]. The phone prompts you for a name.
2. Press [ABC], and the phone asks you for a location.
3. Press [0] then [OK]. The phone asks ARE YOU SURE? Press [OK] or
press [CLR] if you change your mind.
If the list is empty, the phone displays LOCATION EMPTY instead of
ARE YOU SURE?.
Storing Pause and Wait Characters
You can store a 2.5 second pause (p) or a wait (w) character in a stored
number. The reason to do this is for automatic sending of Touch Tones.
For more information on the use of "Pause" and "Wait" characters, see
"Automatically Sending Touch Tones" in Faxback Doc. # 48282.
When entering the number to be stored (see "To Store Numbers and Names"
above.
1. To enter a Pause ("p"), press [MENU] [#].
2. To enter a Wait ("w"), press [MENU] [#] [#].
Note: When storing "w" and "p" characters via storage menu, you must
press and hold [OK] after entering these special characters.
(BR/eb 6/12/98)
Privacy Policy