Nokia 918 Series Cellular Telephone
(170-1242/1222)            Operation                  Faxback Doc. # 48279

The Basics

Switching On/Off

  Press and hold the power key for one second to switch the phone on or
  off.

If your phone has an extendible antenna, extend the antenna fully.  As
with any other radio transmitting device, avoid unnecessary contact with
the antenna when the phone is switched on.

IMPORTANT!:  Do not switch on the phone when cellular phone use is
             prohibited or when it may cause interference or danger.

Making a Call

  Enter the area code + number then [SEND].

If the PIN CALL is set to on, press [SEND] again after the tone.  See "To
Activate PIN CALL" below for details.

Check with your operator to see if you must enter the area code.

If you make a mistake dialing, press [CLR] to erase digits one by one.
Press and hold [CLR] to clear the whole display.

NO SERVICE appears and a beep is given if you try to make a call when your
phone is outside of the cellular service area.

NOT ALLOWED appears if you try to make a restricted call.

PRESS MENU appears if keyguard is on.

IN USE and the dialed phone number will appear on the display.  The call
is connected when the phone number disappears from the display.

Ending a Call

  PRESS [END].

Note:  If you press and hold [END], keyguard is activated.

Answering a Call

  Press [SEND] or any key except the power key.

Note:  If keyguard is active, a call can only be answered with [SEND].

When there is an incoming call, the phone rings and CALL flashes on the
display.  If you have set Ringing Volume to SILENT SERVICE, the keypad and
display lights flash, CALL flashes on the display and the phone makes a
short beep.  You can answer a call any time, even while using the
keyguard, memory of menu functions.

If you don't answer a call, the message 1 CALL MISSED or n CALLS MISSED
will remain on the display until you press any key (except the on/off key)
to clear the display.

Adjusting the Earpiece Volume

  During a call, press [\/] or [/\] to decrease or increase the earpiece
  volume level.  The display must be clear.

Note:  The [\/] and [/\] keys scroll through memory and the menu when not
       in a call.

Last Number Redial

  Clear the display then press [SEND] [SEND].

Last 5 Dialed Numbers

  Clear the display then press [SEND].  Press [\/] until you see the
  number you want.  Then press [SEND] to dial it.

The phone stores the last five phone numbers you called or attempted to
call.  This stack of the five last dialed numbers remains in the phones
memory when the phone is switched off.

If the stack of the last dialed numbers is empty, the message LOCATION
EMPTY will be displayed.

See also "Dialed Calls Memory" in Faxback Doc. # 48280.

Speed Dialing

  Press a location number (1-40) then [SEND].

The phone recalls the number stored in the corresponding location number
in your phone directory (see "The Phone Directory" in Faxback Doc.
# 48280), displays it briefly, then dials it.  If the memory location is
empty, the message LOCATION EMPTY is displayed.

1 Touch Dialing

  Hold [1 o_o] for a few seconds.

The phone dials the number stored in location 1 of your phone directory
(see "The Phone Directory" in Faxback Doc. # 48280) if 1 TOUCH DIALING is
set to on (1 TOUCH ON).

To store the number in the phone directory location 1, see "To Store
Numbers and Names" in Faxback Doc. # 48280.

9 Key Emergency Dialing

  Press and hold [9 WXYZ] for more than 4 seconds.

The phone dials the emergency number programmed into your phone and
displays the message EMERG. CALL TRY if Emergency Key 9 is set to on
(EMERG. 9 ON).

Note:  Official emergency numbers vary by location (e.g., 911 or another
       official emergency number).  However, only one emergency number is
       programmed into your phone to be dialed automatically by one-touch
       emergency dialing, which may not be the proper number in all
       circumstances.

Note:  9 Key Emergency Dialing does not operate when the Keyguard feature
       is activated.  However, an emergency call can be made without
       deactivating the Keyguard by entering the whole emergency number
       programmed into your phone and then pressing [SEND].

Keyguard

  Press and hold [END] to activate Keyguard.

  Press [MENU] then [*] to deactivate Keyguard.  You can also activate
  Keyguard this way.

Keyguard locks the phone's keypad to prevent accidental keypresses (e.g.
when the phone is in a pocket or a bag).

KEYGUARD ACTIVE remains on the display until keyguard is deactivated.

Answering a call with Keyguard active 

  Press [SEND].

During the call, the keypad remains unlocked and the phone can be used
normally.  After the call is ended, keyguard automatically becomes active
again.

The phone cannot be switched off when keyguard is active.

Note:  When keyguard is activated, calls may be possible to the emergency
       number programmed into your phone (e.g., 911 or another official
       emergency number).  However, one-touch 9-key emergency dialing (the
       9 key') does not operate.

To make an emergency call with keyguard active

  Enter the emergency number preprogrammed into your phone (e.g., 911)
  and press [SEND].

The emergency number is displayed only after you have entered the last
digit of the number.

The phone dials the emergency number programmed into the phone and
displays the message EMERG. CALL TRY.

Calling Card Call

When making a call, the call charges can be directed to a selected long
distance carrier, if the card number is sent to the network during the
call setup.  Before making an automatic calling card call, you have to
activate one of the calling card options from the menu function CALLING
CARD.

To make a calling card call

1.  Enter the area code and phone number in the format required by your
    specific calling card (i.e., 0. area code, phone number).

2.  Press and hold [SEND] for more than one second.

    Note:  If no calling card is activated, the phone will make a normal
           call to the phone number entered.

           CARD CALL remains on the display until the access number has
           been sent to the network.  The phone asks you to WAIT FOR
           PROMPT.

3.  After the tone or voice prompt, press [SEND].

    CARD CALL remains on the display; the phone asks you to again WAIT FOR
    PROMPT.

4.  If you get another tone or voice prompt, Press [SEND] again.

Note:  This procedure may not apply to all calling card options programmed
       into your phone.  Please look at the back of your calling card or
       contact your long distance company for more information.

PIN Call

You can activate or deactivate PIN Call, a security feature that requires
a PIN Code every time you make a call.

Note:  If you are using the phone in an area that doesn't require PIN
       dialing, deactivate PIN Call.

To Activate PIN Call

1.  Enter [*] [#] 7462255 [#] (spells [PINCALL]).

2.  The phone asks for your four-digit PIN Code.  Enter your PIN code and
    press [OK].  The phone briefly displays PIN CALL ON.

Making a Call with PIN Call On

1.  Make the call as usual (see "Making a Call" above).

    The phone displays PIN CALL.

2.  After you hear a tone, press [SEND] again.  Wait for your call to be
    connected.

    Note:  If you're in a network that doesn't support PIN CALLS, but your
           phone has PIN Call On, the phone tries to send a PIN anyway.
           To stop this, make the call as usual, then press [CLR] to end
           the PIN Call attempt.

To Deactivate PIN Call

1.  Enter [*] [#] 7462255 [#].  The phone asks for your four-digit PIN
    Code.

2.  Don't enter your PIN Code, just press [OK].  The phone briefly
    displays PIN CALL OFF.

Note:  When the phone is set to PIN CALL ON, an emergency call to the
       emergency number programmed into your phone (e.g., 911 or another
       official emergency number will be dialed as a normal call without
       the PIN code request.

(BR/eb 6/12/98)