Nokia 252 Series Cellular Telephone
(170-1223/4/5/9/30/31) Menus - 1, 2, 3 Faxback Doc. # 47263
Note: The procedures in these documents apply to the following Nokia 252
Series Cellular Telephones (6 total):
170-1223/29 - Woodgrain Finish
170-1224/30 - Gun Metal Finish
170-1225/31 - Black Finish (Sold in California ONLY!)
The only differences between the six phones are those noted above.
The phone's menus and submenus give you access to many features and ways
to customize your phone.
You can use the menus and submenus either with the 'Menu then OK Method'
or the 'Shortcut Method'.
A menu list is shown below and instructions for using the menus follow.
"MENU then OK" Method
1) Press MENU to enter the menu.
2) Press (\/) or (/\) to scroll through menu choices.
3) Press OK to choose a menu.
If there are submenus: press (\/) or (/\) to scroll through the
submenu choices. Press OK to enter a submenu.
4) The current setting is displayed. Press (\/) or (/\) to scroll through
the other choices. Press OK to select one, or press END to exit the
menus without changing anything.
Some menus require you to enter your lock code or security code.
Note: To backstep a menu level at a time, press CLR. To exit the Menu,
press END or press and hold CLR.
Shortcut Method
The menus and submenus are numbered, so you can access them by their
number:
1) Press MENU to enter the menu.
2) Press the number of the menu you want (1-6) within 4 seconds. (Also,
if there are submenus, press the submenu number within 4 seconds.)
The current setting (if applicable) is displayed.
3) Press (\/) or (/\) to scroll through other settings. Press OK to
select a setting or press CLR to exit the menus without changing the
settings.
Note: If you use the shortcut method, the display shows a '_' before the
menu or submenu number in the top right hand corner of the display.
Also, if you use the shortcut method to access Menu 3 1, there is a
5-second delay before the menu appears. To bypass this delay, press MENU
3 1 OK OK.
Using the Menu During a Call
If you press MENU during a call, the phone gives you the In-Call Menu (see
"In Call Menu" in Faxback Doc. # 47270). If you want access to other menu
items, just press and hold MENU for a couple of seconds. Then use the
menus as you normally would.
List of Menu Functions
1. Phone Book
1. Find Name
2. Save Name & Number
3. Edit Name or Number
4. Erase from Phone Book
5. Phone Book Status
2. Call Log
1. Dialed Calls
2. Erase all Recent Calls
3. Call Timers
3. Phone Settings
1. Ringing Options
2. Ringing Volume
3. Ringing tone
4. Keypad Tones
5. Lights
6. 1-Touch Dialing
7. Emergency 9 dialing
8. Language
9. Phone Number
10. Automatic Answer
11. Automatic Redial
4. Security Settings
1. Change Lock Code
2. Change Security Code
3. Restore Factory Settings
5. Call Settings
1. Calling Card
2. Calling Options
6. Lock Phone
Prevents outgoing calls and access to all phone functions.
In-Call Menu
This is available only during calls. Give the MENU key a short press to
access these options:
Mute
Send DTMF
Reminder Message
Displays a personalized message when you switch your phone on.
Phone Book (Menu 1)
To access Menu 1, press MENU then OK.
Find Name (Menu 1 1)
1. Press MENU then OK.
2. You'll see FIND NAME. Press OK again. The phone prompts you to enter
a name.
3. Enter the first few letters of the name, then press (\/), or just
press (\/) to scroll through stored names.
Note: To see stored numbers, press ABC, then press (\/) to scroll through
them.
Save Name & Number (Menu 1 2)
1. Press MENU then OK then (\/) to scroll to SAVE NAME & NUMBER. Press
OK.
2. Enter name and press OK. Enter number and press OK. The phone suggests
a location for saving the entry.
3. Press OK, or enter another location number then press OK. The phone
displays SAVED and the remaining available memory.
Edit Name or Number (Menu 1 3)
1. Recall the number from memory.
2. Press MENU then OK then (\/) to scroll to EDIT NAME OR NUMBER. Press
OK.
3. Edit the name: use the CLR key to delete characters, use (\/) and (/\)
to move the cursor, and enter new characters as required.
4. Edit the number: press ABC. Use the CLR key to delete digits, use
(\/) and (/\) to move the cursor, and enter new digits as required.
Press OK.
5. At SAVE IN LOCATION? press OK. If you did not change the name, or the
name you have entered matches one already stored, then REPLACE? will
be displayed; press OK to replace the contents with the new (edited)
name and number.
Erase From Phone Book (Menu 1 4)
Note: Be careful when erasing -- it can't be undone!
1. Press MENU then OK then (\/) to scroll to ERASE FROM PHONE BOOK. Press
OK.
2. Press (\/) to move the pointer to your choice. Press OK to choose it.
If you choose Erase All, the phone asks you to confirm. Press OK when you
see ARE YOU SURE?, or press CLR to exit without erasing.
If you choose One by One, the phone displays Erase name:. Either enter the
first few letters of the name then press (\/) or just press (\/) to scroll
through stored names. Press ABC to see phone numbers to erase. When you
see the name or number you want to erase, press OK, or press CLR if you
change your mind and do not want to erase.
Phone Book Status (Menu 1 5)
1. Press MENU then OK then (\/) to scroll to PHONE BOOK STATUS. Press OK.
2. The phone displays the percentage of memory available.
Call Log (Menu 2)
To access Menu 2, press MENU then (\/). You'll see CALL LOG; press OK.
Dialed Calls (Menu 2 1)
The phone automatically stores the last ten numbers you called or
attempted to call. The same phone number isn't stored twice in the list.
When you dial a number that already exists in the list, the dialed number
is moved to the top.
The Dialed Calls list remains in the phone's memory when the phone is
switched off. If you want to erase it, use Menu 2 2.
1. Press MENU (\/). You'll see CALL LOG; press OK.
2. You'll see DIALED CALLS. Press OK again.
3. Press (\/) to scroll through the last 10 numbers you have dialed.
Press SEND to dial one of the numbers.
Erase All Recent Calls (Menu 2 2)
Note: This menu erases Dialed Calls, and can't be undone!
1. Press MENU (\/). You'll see CALL LOG; press OK.
2. Press (\/) to scroll to ERASE ALL RECENT CALLS. Press OK.
3. The phone asks ARE YOU SURE?. Press OK to erase, or press CLR to exit
without erasing.
Call Timers (Menu 2 3)
1. Press MENU (\/). You'll see CALL LOG; press OK.
2. Press (\/) to scroll to CALL TIMERS. Press OK.
3. Press (\/) to scroll through the options. Press OK to choose the one
you want. (You'll need your security code to clear the timers.)
LAST CALL shows the duration of the last call in hours, minutes, and
seconds. If you are in a call, the phone shows the duration of the call in
progress. (Make sure you hold MENU for a couple of seconds during a call
to get to the regular menu and not the In-Call menu.)
ALL CALLS shows the total amount of time spent on calls since the timer
was last reset. ALL CALLS applies to the phone number currently selected
for your phone.
LIFE TIMER shows the total amount of time you have spent on calls in hours
and minutes. This number cannot be reset. (You can also select Life Timer
by pressing and holding the # key for about 4 seconds.)
CLEAR TIMERS resets all the timers to zero (except the Life Timer).
Note: CLEAR TIMERS cannot be undone!
Note: The actual invoice for calls by your cellular service provider may
vary, depending upon network features, rounding-off for billing,
taxes and so on.
Phone Settings (Menu 3)
To access Menu 3, press MENU, then (\/) until you see PHONE SETTINGS.
Press OK.
Ringing Options (Menu 3 1)
You can choose how you want the phone to indicate there is an incoming
call.
1. Press MENU then (\/) until you see PHONE SETTINGS. Press OK.
2. You'll see RINGING OPTIONS and the current setting. Press OK if you
want to change it.
3. Press (\/) to move the pointer to the choice you want. Press OK to
select one.
For Ring+Vibra or Vibrate to work, you need the Vibra battery (BKL-6).
If you choose Silent, the phone displays SILENT when you aren't using the
other functions of the phone. This message is to remind you that the
ringing tone is set to Off.
Note: When SILENT is selected, all tones, except for the charger-connected
tone, are also switched off.
Ringing Volume (Menu 3 2)
With this menu you choose the ringing volume. As you scroll through each
of the 5 volume levels, the phone rings so you can hear each level.
1. Press MENU then (\/) until you see PHONE SETTINGS. Press OK.
2. Press (\/) to scroll to RINGING VOLUME and the current setting. Press
OK if you want to change it.
3. Press (\/) to move the pointer. Press OK for the ringing volume you
want.
Ringing Tone (Menu 3 3)
There are 6 different ring tones to choose from. As you scroll through
each type, the phone rings so you can hear each one.
1. Press MENU then (\/) until you see PHONE SETTINGS. Press OK.
2. Press (\/) to scroll to RINGING TONE and the current setting. Press OK
if you want to change it.
3. Press (\/) to move the pointer. Press OK for the ringing tone you
want.
Keypad Tones (Menu 3 4)
When you press the buttons on your phone, the phone beeps (the sound
depends on which key you press). With this menu, you can choose between
three volume levels or you can turn the keypad tones off.
1. Press MENU then (\/) until you see PHONE SETTINGS. Press OK.
2. Press (\/) to scroll to KEYPAD TONES and the current setting. Press OK
if you want to change it.
3. Press (\/) to move the pointer. Press OK to choose the one you want,
or select Off.
Note: You can still send Touch Tones even when the keypad tones are
switched off.
Note: Keypad tones are set to Off when you choose Silent in "Ringing
Options (menu 3 1)". See above.
Lights (Menu 3 5)
The Keypad and phone display have lights to make them easy to read. This
menu allows you to set the phone's lights On or Off.
1. Press MENU then (\/) until you see PHONE SETTINGS. Press OK.
2. Press (\/) to scroll to LIGHTS and the current setting. Press OK if
you want to change it.
3. Press (\/) to move the pointer. Press OK to choose On or Off.
Lights On
The keypad and display backlights are on for 15 seconds after the last
keypress.
Lights Off
The lights are off permanently, except if Silent ringing is selected. Then
they flash to indicate an incoming call.
1-Touch Dialing (Menu 3 6)
This menu gives you the option of dialing memory locations 1-8 by pressing
and holding a single number key for 2 seconds (location 1 is recommended
to be used for the Voice Mailbox Number). For example, pressing and
holding 5 dials the number stored in location 5.
1. Press MENU then (\/) until you see PHONE SETTINGS. Press OK.
2. Press (\/) to scroll to 1-TOUCH DIALING and the current setting. Press
OK if you want to change it.
3. Press (\/) to move the pointer. Press OK to choose On or Off.
With 1-Touch Dialing On, you can dial the number stored in any of the
locations 1 to 8, by pressing and holding the corresponding number key. If
you press and hold 9, the phone dials your voice mailbox number if you
have stored it in this location.
Note: 1-Touch Dialing does not operate when Keyguard is On, or when a
call is already established.
If you press and hold 9, the phone attempts to make a call to the
emergency number pre-programmed into your phone if you have Emergency 9
Dialing (Menu 3 7) set to On.
Emergency 9 Dialing (Menu 3 7)
You may dial the emergency number programmed in your phone by your dealer,
by pressing and holding the 9 key, only if Menu 3 7 is set to On.
1. Press MENU then (\/) until you see PHONE SETTINGS. Press OK.
2. Press (\/) to scroll to EMERGENCY 9 DIALING and the current setting.
Press OK if you want to change it.
3. Press (\/) to move the pointer. Press OK to choose On or Off.
LANGUAGE (Menu 3 8)
The menus and messages can be displayed in English, French, Spanish, or
Portuguese.
1. Press MENU then (\/) until you see PHONE SETTINGS. Press OK.
2. Press (\/) to scroll to LANGUAGE and the current setting. Press OK if
you want to change it.
3. Press (\/) to move the pointer to your choice. Press OK to select an
option.
Phone Number (Menu 3 9)
Your phone can have two different telephone numbers. This menu lets you
choose which telephone number to use.
Note: In order to have two different telephone numbers, you must subscribe
to them through your cellular operator(s).
1. Press MENU then (\/) until you see PHONE SETTINGS. Press OK.
2. Press (\/) to scroll to PHONE NUMBER and the current phone number.
Press OK if you want to change it.
3. Press (\/) to move the pointer to the number you want (if there are
two available). Press OK.
Notes: If only one phone number is programmed into your phone, you only
see that number in this menu.
The phone can't use both numbers at the same time and you can't
change the number during a call.
If your phone is set to your first number, you can only receive
calls via that number. You may be able to forward calls from your
second number to your first number so you don't miss any calls if
this service is available from your cellular service provider. For
more information, please contact your cellular service provider.
Automatic Answer (Menu 3 10)
Note: This feature applies only if the phone is in a handsfree car kit.
With Automatic Answer On, the phone automatically answers after 4 seconds.
1. Press MENU then (\/) until you see PHONE SETTINGS. Press OK.
2. Press (\/) to scroll to AUTOMATIC ANSWER and the current setting.
Press OK if you want to change it.
3. Press (\/) to move the pointer. Press OK to choose On or Off.
Automatic Redial (Menu 3 11)
Sometimes the cellular network is busy and your call can't go through.
You get a SYSTEM BUSY... message and are asked to redial. If Automatic
Redial is set to On, the phone automatically tries 3 more times to connect
the call. If the call connects, the phone beeps to notify you.
1. Press MENU then (\/) until you see PHONE SETTINGS. Press OK.
2. Press (\/) to scroll to AUTOMATIC REDIAL and the current setting.
Press OK if you want to change it.
3. Press (\/) to move the pointer. Press OK to choose On or Off.
(BR/eb 4/20/98)
Privacy Policy