Cellular Telephone
(170-1204/05/06) Special Features Faxback Doc. # 46529
Call Features
These features are designed to simplify operation or provide additional
convenience during special situations. We recommend that you experiment
with these before using them during actual calls.
Display Own Telephone Number
Press [RCL], [#]. If your telephone is registered in two systems, the
number displayed will be the one currently active.
Call in Absence Indicator
If an incoming call is unanswered, CALL is displayed for 6 seconds.
Pressing any key but [CLR] redisplays the message to inform you of the
call attempt. You must press [CLR] to cancel message.
Mute Microphone
This feature allows you to confer privately with others during a
conversation. To mute the microphone, press [FCN], [16]. The unit will
display MUtE. To reinstate the microphone, press [FCN], [16] again.
To help remember which key to use, note that the M for Mute appears on 16.
The mute feature is canceled when you end your call.
Hands-Free Operation
When using a vehicular accessory, the telephone is in hands-free operation
when HF displays. To toggle between hands-free and handset operation,
press [FCN], [17].
Feature Menu
Some of your telephone's call features are accessed by a Feature Menu,
that permits review, selection, and cancellation of these features
through the keypad and display.
To access features through the menu, press [FCN], [1]. The unit will
display the first menu feature. The following chart shows all features
available through the menu, and the pages where detailed information can
be found.
Feature Faxback Doc. # Enabled Disabled
Automatic Answer 46529 (below) 0 -
Automatic Lock 46530 0 -
Emergency Dialing 46530 - 0
Pin Code Activation 46529 (below) 0 -
Reminder Beeps 46529 (below) 0 -
Signal Strength Meter 46525 - 0
VOX 46526 0 -
Review (scroll) the menu features with [*] and [#]. The display will
indicate the feature's status and name. When using the menu, information
is displayed in two cycles.
The feature status is indicated at the left of the display ( _ if the
feature is off; 0, if the feature is on. Refer to the chart above).
Toggle the displayed feature on and off with [CLR].
To exit the menu, press [END].
Features Status Review
When the telephone is turned on, 0 in the display indicates that one or
more features have been selected or changed from their standard settings.
Feature Status Review permits you to scroll through your operating
settings for your reference.
To review status, press [FCN], [10], [19], [RCL]. press [*] and [#]
repeatedly to scroll through the messages. To end review, press [END].
Display Description Faxback Doc. #
AnSWEr Automatic Answer (below)
AUtoLoc Automatic Lock 46530
EMr OFF Emergency Dialing 46530
HOME System Type Selection 46527
LEVEL 1 Service Levels 46530
Pin Pin Code activated (below)
PrEF'dS ,dS System Type Selection 46527
rMd OFF Reminder Beeps deactivated (below)
SCAn A System Type Selection 46527
SCAn Ab System Type Selection 46527
SCAn b System Type Selection 46527
SCAn bA System Type Selection 46527
S,9 oFF Signal Strength Meter 46525
Std Features Set as Standard 46530
voX Voice Operated Transmission 46526
Tone Dialing (Two - Part Calling)
Your telephone provides the standard Dual Tone Multi-Frequency (DTMF)
signals typically used to access alternate long distance services, signal
pagers, etc.
Generally, these services use a two-part procedure; first a call is placed
from the memory or through the keypad to a central telephone number, then
a secondary dial tone is heard and the additional tone digits are sent.
1. To Tone Dial from the keypad, make the initial call.
2. Append additional tone digits using the keypad. The tones are
automatically sent as you press the keys. Do not press [SND].
To tone Dial from a memory location, place the initial call. Recall from
memory (using [RCL], location number) the number you wish to send as DTMF
digits. Press [RCL], [SND]. Repeat these steps as required to send
separate groups of numbers.
Automatic Pause (Memory Linking)
Two - Part Calling, as described above, can be automated by a unique
feature which permits the programming and memory storage of pauses between
groups of numbers. When recalled or sent, the telephone stops transmitting
at the pause and waits for your response (i.e., secondary dial tone).
To Create a Linked Sequence
1. Enter the first group of numbers from the keypad or recall them from
memory using [RCL].
2. Insert a pause by pressing [FCN], [SND]. o will appear where the pause
is inserted.
3. Enter the next group of numbers or recall them from memory by pressing
[FCN], [RCL], and entering the two-digit location number.
4. Repeat this sequence for as many groups as you wish up to a maximum of
16 digits. (Each pause occupies a digit.) If you wish, you may store
this number in memory by pressing [STO] and a two-digit location
number.
To Place a Linked Call
1. Create or recall a linked number.
2. Press [SND] to transmit the first group of numbers, prior to the first
pause.
3. After waiting for the system response, press [RCL], [SND] to send the
second group of numbers as DTMF tones.
4. To repeat the sequence press [RCL], [SND], if needed, until all digit
groups are sent.
Automatic Answer
This feature permits you to answer calls without pressing [SND]. When your
telephone receives a call it will ring twice. Answer the call by lifting
the unit to your ear.
1. To select this feature, press [FCN], [1] to access the Feature Menu.
2. Scroll the menu with [*] and [#] until [ _AnSWr ] [ _AUtO ] displays.
3. Use [CLR] to toggle this feature on and off. See above for more
information on using the Feature Menu.
4. To exit the Feature Menu, press [END].
Reminder Beep (on selected models only)
Your cellular carrier may offer enhanced features such as Short Messaging.
Ask your Cellular Service Provider if this is supported in your system.
If Short Messaging is not supported in your system, Reminder Beep
selection will have no effect.
Reminder Beep is an audible notification to alert the user that they have
received a message. It will beep every two minutes until the new messages
have been read.
Disable this feature through the Feature Menu.
1. To enter the Feature Menu, press [FCN], [1]. Scroll the menu by
pressing [*] and [#] until the desired feature displays. Press [CLR]
to toggle the feature displays. Press [CLR] to toggle the feature on
(0) or off ( _ ). Press [END] to exit.
PIN Code Activation (on selected models only)
Your cellular carrier may require a Personal Identification Number (PIN)
when placing outbound calls. This code assures the cellular system that
the person placing the call is an authorized user. Ask your Cellular
Service Provider if this is required in your system.
First select the feature in the Feature Menu by following instructions
listed on above. Then store your PIN Code in Memory Location 07 ("P"
for PIN), by following instructions on Faxback Doc. # 46528. A maximum
of 7 digits are allowed.
To place an outbound call using PIN code:
For example:
1. Enter the number you wish to call.
2. Press [SND], [*].
3. Wait for double tone "Beep Beep".
4. Press [SND].
The phone will automatically send the PIN Code (stored in Memory Location
07).
If you enter a service area which does not require a PIN Code, disable
the feature in the Feature Menu.
Call Timers
Call Timers provide a useful means of monitoring the air-time spent in
conversation. These operate in the background and can be displayed at
any time.
Each timer begins counting as a cellular channel is assigned, or when the
phone rings to signal an incoming call. If an incoming call is not
answered, the timers revert to their previous values.
Individual Call Timer
This timer accumulates the air-time of the unit in minutes and seconds for
each call.
This timer automatically resets before a new call is placed and when power
is turned off. To display, press [RCL], [#], [#].
Resettable Call Timer
This timer accumulates the unit's air-time in minutes from the point at
which it is reset.
You may wish to reset this timer in concert with your monthly billing
cycle. To display press [RCL], [#], [#], [#]. To reset, press [FCN],
[10], [17], [CLR].
Cumulative Call Timer
This timer accumulates the unit's total air-time in minutes, starting with
the initial factory testing. To display, press [RCL], [#], [#], [#], [#].
The Cumulative Call Timer cannot be reset.
(LB/EB 2/18/98)
Privacy Policy