Ericsson DH 318 Digital Cellular Phone
(170-1201) Memory Faxback Doc. # 35276
Storing and Recalling Numbers in Memory
You can store phone numbers and associated names in your phone's memory to
use for Recall dialing, Speed Dial, and Super Dial. Each number you store
can be up to 32 digits in length and any names you store can be up to 24
characters in length.
NOTE: The number of phone numbers stated which your phone can store is
based on each number containing 12 digits and having an eight charac-
ter name stored with the number. Storing longer numbers and names
reduces the amount of memory available and reduces the actual numbers
you can store. You can view the percentage of memory used and avail-
able through the Memory menu. See Faxback Doc. # 35279.
Storing a Number and Name in Memory
There are two ways you can do this:
Through the Memory menu
Store a number already shown in the display
Storing a Number by Using the Memory Menu
1. Press MENU/ \/ to access Menu mode.
2. Press MENU/ \/ or RCL/ /\ until the menu pointer (>) is beside Memory.
3. Press YES to open the Memory menu.
4. Press MENU/ \/ or RCL/ /\ until the menu pointer is beside Store Mem.
5. Press YES to open the Store Mem selection. The next open memory
location is shown in the display.
6. Enter a name you want associated with the telephone number you are
going to store. The following table shows which keys to press and the
number of times you must press them to enter letters.
7. Press MENU/ \/ to move the cursor to the No: line in the display.
8. Enter the phone number you want to store.
9. Press YES to store the number. STORED IN MEMORY! is shown in the
display.
____\
| Hint > To enter letters from the keypad, you must press a key one, two,
/ three, or four times, depending on which letter you want to enter.
The following table lists the keys and the number of times you
must press it to enter a particular letter.
Press this Number of Times
One Two Three Four
1 Space & 1 space
2 A B C 2
3 D E F 3
4 G H I 4
5 J K L 5
6 M N 0 6
7 P Q R S
8 T U V 8
9 W X Y Z
0 0
* , ' " *
# - . ? #
Storing a Number Shown in the Display
1. Enter a number.
2. With the number shown in the display, press MENU/ \/ to access Menu
mode.
3. Press MENU/ \/ or RCL/ /\ until the menu pointer is beside Memory.
4. Press YES to open the Memory menu.
5. Press MENU/ \/ until the menu pointer is beside Store Mem.
6. Press YES to open the Store Mem selection. The number is shown in the
No: line of the Store Mem display.
7. If you want to enter a name to be associated with this number, enter it
now on the Name: line. See the table above for information on entering
letters.
8. Press YES to store the number in memory.
Specifying a Memory Location
If you want to store a phone number in a specific memory location, follow
the previous steps for entering the number and name, then press MENU/ \/ to
move the cursor to the STORE line, then enter the memory location number.
Phone numbers stored in locations 1 through 9 can be used with the Super
Dial feature. All one and two digit memory locations can be used with the
Speed Dial feature.
Storing a Number in Secure Memory
To store a number in secure memory, follow the previously described steps
for entering a name and number, then press and hold YES. The phone prompts
you to enter your security code. If you enter the correct code, the number
is stored and Number Stored Securely in Memory is shown in the display. A
number stored in secure memory cannot be recalled unless you enter the
correct security code.
Recalling a Number Directly From Memory
There are two ways to get to the Recall Mem menu selection:
Start from the beginning of Menu mode
Press RCL/ /\ to go directly to the Recall Mem selection.
Recalling a Number From the Memory Menu
1. Press MENU/ \/ to access Menu mode.
2. Press MENU/ \/ or RCL/ /\ until the menu pointer is beside Memory.
3. Press YES to open the Memory menu.
4. Press MENU/ \/ or RCL/ /\ until the menu pointer is beside Recall Mem.
5. Press YES to open the Recall Mem. display. You can recall a number in
memory by the location number or by the name if there is a name stored
with the number.
6a. If you want to recall the number by searching for the name, enter the
letters of the name in the Name: line. You can enter just a few letters
of the name or the complete name. If you enter just a few letters, the
phone finds the first name in memory that begins with the letters you
entered. See the table above for information on entering letters.
OR
6b. If you want to search for the location number, press MENU/ \/ until the
cursor is on the Recall: line and enter the number. The number is shown
in the display.
7. You can place a call to the number in the display by pressing YES.
Recalling a Number From Secure Memory
1. Follow the previously described steps for opening Recall Mem. in the
Memory menu.
2. Press MENU/ \/ until the cursor is on the RECALL: line.
3. Enter the location of the number stored in secure memory.
4. Press RCL/ /\. Security Code: is shown in the display.
5. Enter your security code.
6. If you enter the correct security code, the number is shown in the
display.
Altering a Number in Memory
You can add digits to a number in memory or delete and replace digits in a
number stored in memory. To do this:
1. Recall the number as previously described.
2. When the number is shown in the display, press MENU/ \/ to move the
cursor to the No: line.
3. To add digits to the end of the number, just enter the digits.
4. To replace digits, press CLR to erase the digits you want to change and
then enter the new digits.
5. Press Yes to store the altered number.
Erasing a Number From Memory
1. Press MENU/ \/. The Main Menu is shown in the display.
2. Press MENU/ \/ or RCL/ /\ until the menu printer is beside Memory.
3. Press YES. The Memory menu is shown in the display.
4. Press MENU/ \/ or RCL/ /\ until the menu pointer is beside RCL Mem.
5. Press YES.
6. Press MENU/ \/ or RCL/ /\ until the number and name you want to erase
is shown in the display.
7. Press and hold CLR. Erase memory? Location xxx is shown in the display.
8. Press YES to erase the number from memory. Memory is erased! is shown
briefly in the display.
(BR/EB 10/25/96)
Privacy Policy