Nokia CT-201 Cellular Telephone
(170-1005)                 Operation                  Faxback Doc. # 35120

Switching ON (or OFF)

Extend the antenna fully.

As with any other radio transmitting device, avoid prolonged contact with
the antenna when the phone is switched on.

1.  Press the PWR key and hold it for at least one second.

    The phone will carry out a short self-test sequence, then briefly
    Display its number or name associated with the number (operator,
    dealer name).

2.  When the ON indicator appears on the display the phone is ready for
    use.

    If NO SVC appears it likely means that you are outside the cellular
    Service area and the network cannot serve you.

    A cellular phone can only send and receive calls when it is switched
    on.

3.  Press the PWR key and hold it for at least one second to switch the
    phone off.

Placing A Call

Fully extend the antenna before sending or receiving a call.

Note:  Push in the antenna when you are not using the phone.

You can use the phone without extending the antenna in a good coverage
area (see "Signal Strength" below).

1.  Key in the number (include the area code, if you're making a long
    distance call).

    If you make a mistake, press the CLR key to delete the last keystroke;
    or to clear the whole display, press and hold the CLR key.

2.  The number will appear on the display.

3.  Press SEND.

4.  The IN USE indicator will appear, and the number will disappear from
    the display.

5.  Lift the phone to your ear, and wait until your call is answered.

6.  When you have finished the call, press END.

If the message NO SERVICE appears, you are outside the cellular service
area.

If the message LOCKED appears on the display when you try to make a call,
your phone has been electronically LOCKED see ("Locking The Phone").  You
can still make emergency calls and calls to the number in memory location
48, when the phone is locked.

Receiving A Call

1.  When there is an incoming call, the phone rings and the CALL message
    flashes on the display.

    If the ringing tone has been switched off - the SILENT SERVICE feature
    Has been selected for privacy or other reasons - the keypad and
    display lights will flash instead and only one short "beep" will be
    given.  (See 'Setting The Ringing Volume' on Faxback Doc. # 35119).

2.  Press SEND and lift the phone to your ear.  (For your comfort do not
    lift the phone to your ear before pressing SEND.)

3.  When you have finished speaking, press END.

If you don't answer the call, the CALL message will remain on the display
(showing that someone has tried to phone you).  Press any key to clear the
display.

Signal Strength

The quality of your call depends on the strength of the cellular signal in
your area.  The phone displays current signal strength as a series of bars
on the left side of the display screen. The more bars the better the 
signal.

If the signal is poor, try moving the phone slightly to improve reception.
If you are using the phone in a building, it may be necessary to move near
a window, or outdoors for better reception.  

Volume Keys

The earpiece volume can be controlled by the volume key on the right side
of the phone.

Use the upper part of the key to increase and the lower part of the key to
decrease volume level.  The volume level is shown on the display. VOLUME 1
indicates the lowest and VOLUME 5 the highest volume level.  If you try to
increase or decrease the volume level over these values, an error "beep" 
is given.

Last Number Redial

The last number dialed can re redialed automatically without re-entering 
it. (The number can still be retrieved even if the phone has been switched 
off and back on.)

1.  With the display clear, press SEND.

2.  The number you last called will appear on the display and is
    automatically redialed.

Last number redial can also be used from the menu:

1.  Press MENU.

2.  Press /\ or \/ repeatedly, until RECALL LAST appears on the display.

3.  Press STO.  The last number you dialed will appear on the display.

4.  Press SEND to make the call.

Speed Dialing

Speed dialing is the quickest way to recall and dial a telephone number.

When you have stored a frequently used phone number in the memory you can
use the memory location number or name when dialing the stored number. 
(See "Storing Information").

1.  Key in the number of the memory location (e.g. 0, 2) or the name
    stored there (name uses the ALPHA mode).

2.  Press SEND.

The phone will recall the telephone number or name from memory, display it
briefly, and then dial it.

Wait until your call is answered.

The Menu Facility

The menu allows you to operate or check the setting of certain features.
Although the menu method can take longer than the alternative shortcut, it
is often easier to remember.

1.  Press MENU.

2.  The display will read "USE TO VIEW". Use either \/ or /\ to step
    forward or backward through the list of functions available. Press STO
    when the desired function is displayed.

3.  Use the \/ or /\ to change the setting of the function.  (The current
    setting is displayed first.)

4.  Press STO to set the new status (the one which is displayed).

5.  Use the CLR key to exit the menu function.

Each menu function can also be controlled by a shortcut, the phone 
displays the shortcut number at the top right corner of the display.

(YO/EB 10/14/96)
(EB Rev. 9/22/00)

Privacy Policy