NOKIA 101 Cellular Phone
(170-1095) Operation Faxback Doc. # 34896
SWITCHING ON (OR OFF)
1. Press the PWR key and hold it for at least 2 seconds.
The phone will carry out a short self-test sequence, then briefly display
its programmed name or number.
2. When the ON indictor appears on the display, the phone is ready for use.
If NO SVC appears it likely means that you are outside the cellular service
area and the network cannot serve you.
A cellular phone can only send and receive calls when it is switched on.
3. Press the PWR key and hold it for at least 2 seconds to switch the
phone off.
PLACING A CALL
Fully extend the antenna before sending or receiving a call.
NOTE: Push in the antenna when you are not using the phone.
You can use the phone without extending the antenna in a good coverage area
(see `Signal Strength', below).
1. Key in the number (include the area code, if you're making a long
distance call).
If you make a mistake, press the CLR key to delete the last keystroke;
or to clear the whole display, press and hold the CLR key.
2. The number will appear on the display.
3. Press SEND.
4. The IN USE indicator will appear, and the number will disappear from the
display.
5. Lift the phone to your ear, and wait until your call is answered.
6. When you have finished the call, press END.
If the message NO SERVICE appears, you are outside the cellular service
area.
If the message LOCKED appears on the display when you try to make a call,
your phone has been electronically LOCKED (see `Locking the Phone', on
Faxback Doc. # 34898). You can still make emergency calls and calls to the
number in memory location 48 when the phone is locked.
RECEIVING A CALL
1. When there is an incoming call, the phone rings and the CALL message
flashes on the display.
If the ringing tone has been switched off - the SILENT SERVICE feature
has been selected for privacy or other reasons - the keypad and display
lights will flash instead and only one short "beep" will be given. (See
`Setting the Ringing Volume' on Faxback Doc. # 34898).
2. Press SEND and lift the phone to your ear.
(For your comfort do not lift the phone to your ear before pressing
SEND.)
3. When you have finished speaking, press END.
If you don't answer the call, the CALL message will remain on the
display (showing that someone has tried to phone you). Press any key
to clear the display.
SIGNAL STRENGTH
The quality of your call depends on the strength of the cellular signal in
your area. The phone displays current signal strength as a series of bars
on the left side of the display screen. The more bars, the better the
signal. If the signal is poor, try moving the phone slightly to improve
reception. If you are using the phone in a building, it may be necessary
to move near a window, or outdoors for better reception.
VOLUME KEYS
The earpiece volume can be controlled by the volume keys \/ /\.
Use /\ key to increase and \/ key to decrease volume level. The volume
level is shown on the display. VOLUME 1 indicates the lowest and VOLUME 5
the highest volume level. If you try to increase or decrease the volume
level over these values, an error "Beep" is given. (Note that these keys
also act as scroll keys within the recall and menu operations.)
LAST NUMBER REDIAL
The last number dialed can be redialed automatically without re-entering it.
(The number can still be retrieved even if the phone has been switched off
and back on.)
1. With the display clear, press SEND.
2. The number you last called will appear on the display and is
automatically redialed.
Last number redial can also be used from the menu:
1. Press MENU.
2. Press \/ or /\ repeatedly, until RECALL LAST appears on the display.
3. Press STO. The last number you dialed will appear on the display.
4. Press SEND to make the call.
SPEED DIALING
Speed dialing is the quickest way to recall and dial a telephone number.
When you have stored a frequently used phone number in the memory you can
use the memory location number or name when dialing the stored number. (See
`Storing Information' on Faxback Doc. # 34897).
1. Key in the number of the memory location (e.g. 0.2) or the name stored
there (name uses the ALPHA mode).
2. Press SEND.
The phone will recall the telephone number or name from memory, display it
briefly, and then dial it.
Wait until your call is answered.
THE MENU FACILITY
The menu allows you to operate or check the setting of certain features.
Although the menu method can take longer than the alternative shortcut, it
is often easier to remember.
1. Press MENU.
2. The display will read `USE TO VIEW'. USE either \/ or /\ to step
forward or backward through the list of functions available. Press STO
when the desired function is displayed.
3. Use the \/ or /\ to change the setting of the function. (The current
setting is displayed first).
4. Press STO to set the new status (the one which is displayed).
5. Use the CLR key to exit the menu function.
Each menu function can also be controlled by a shortcut; the phone
displays the shortcut number at the top right corner of the display.
MENU SHORTCUTS
To activate the shortcut function simply press MENU followed by the shortcut
number, (eg. MENU 5 for keypad tones).
The menu functions available are:
Menu Function/Description Shortcut
LOCK PHONE MENU + 0
Lock phone, unlock phone
SYSTEM SELECT MENU + 1
(system feature) select roaming option
RECALL LAST MENU + 2
recall last number
CALL TIMERS MENU + 3
displays length of calls; reset timers
LIGHTS ON OFF MENU + 4
set lights off; or off after 15 sec.
KEYPAD TONES MENU + 5
switch keypad tones on/off
RINGING VOLUME MENU + 6
select volume of ringing tone
NAM SELECT MENU + 7
view and select cellular number, network
SEND DTMF MENU + 8
send DTMF tones (during a call)
For further information on menu functions see the `Additional Features'
section on Faxback Doc. # 34898.
(BR/EB 10/4/96)
Privacy Policy