ET-532 10-Channel Cordless Telephone
(430-1032)                 Operation                  Faxback Doc. # 31153

Your ET-532's LCD display shows telephone numbers as you dial them or when
you recall hem from memory.  It shows the current channel number and lets
you know when battery power is growing weak or the phone is out of range of
the base.  The display also shows indicators when you press FLASH or PAUSE,
or when you switch from tone to pulse dialing.

MAKING/ANSWERING A CALL

You can use your cordless telephone in two ways: at the base or away from
the base.

USING THE HANDSET AT THE BASE

You can use the handset at the base like a regular corded telephone.  Just
set POWER to ON and place the handset in the cradle.

To answer a call, just list the handset from the base.

To make a call, lift the handset from the base and press TALK so the keypad
and the CHARGE/TALK indicator on the base light.

NOTE:  CH   and the currently used channel number appear on the display. 
       This number might change when you return the handset to the base.

To disconnect a call, replace the handset on the base.

USING THE HANDSET AWAY FROM THE BASE

To make or answer a call, set POWER to ON and press TALK.  The keypad
and CHARGE/TALK indicator light.

To disconnect a call, press TALK so the keypad light and the CHARGE/
TALK indicator turn off.

NOTES:  CH and the currently used channel number appear on the display.

        To conserve battery power, you can turn off the handset's power 
        when you are not making or answering a call.

        You can make or answer a call on a phone on the same line as the
        cordless phone, even if the handset is away from the base.

        RANGE appears when the distance from the handset to the base is
        out of the phone's range.

        The keypad lights on the handset turn off if no button is 
        pressed for more than 13 seconds.  

REDUCING INTERFERENCE

To reduce interference, press CH to switch to the next channel (10 channels
in all) until you receive the best reception.  CH and the channel number
appear on the display.

USING REDIAL

To quickly redial the last number you dialed, simply lift the handset from
the base and press TALK again so the CHARGE/TALK indicator lights; and then
press REDIAL.  The redialed number appears on the display.

The redial memory holds up to 80 digits in the tone mode or 81 digits in
the pulse mode.  The redial memory also holds pause entries.

NOTE:  We recommend you not use REDIAL to dial numbers that include a tone
       (*) entry (see "Using Tone Services on a Pulse Line").

USING FLASH

Use FLASH on the handset to perform the switchhook operation for special
services, such as call waiting.

For example, if you have call waiting, press FLASH to take an incoming call
without disconnecting the current call.  FLASH appears.  Press FLASH again
to return to the first call.

NOTES:  If you do not have special phone services, pressing FLASH might
        disconnect the current call.

        The redial memory does not store a FLASH entry or any digits
        entered after you press FLASH.

USING TONE SERVICES ON A PULSE LINE

Some special services, such as bank by phone, require tone signals.  If you
have pulse service, you can still use these special tone services by
following these steps.

1.  Set TONE/PULSE on the base to PULSE.

2.  Dial the service's main number.

3.  When the service answers, press * on the keypad.  A appears on the
    display.  Then dial the additional numbers.  The phone sends these
    numbers as tone signals.

4.  When you complete the call, place the handset on the cradle or press
    TALK to disconnect the call.  The phone automatically reset to the
    pulse mode.

NOTE:  We recommend you not use REDIAL to dial numbers that include a tone
       (*) entry.

USING PAGE

The PAGE feature allows someone at the base to page you at the handset.  It
also helps you find the handset if you misplaced it.

With the handset's power on, the handset beeps four sets of two beeps when
you press PAGE on the base.  The TALK key on the handset flashes, and the
channel number and INT appear on the display.

NOTE:  The handset will not beep during the a call.

MEMORY DIALING

You can store up to 30 phone numbers for quick and easy dialing.  Each
stored number can be up to 16 digits long.

NOTES:  If TONE/PULSE is set to PULSE and you want to use tone dialing
        for a memory number, you must store the tone entry along with
        the number.

        To keep your accounts secure, we recommend you do NOT store your
        personal access code for services such as bank-by-phone in a memory
        location.


(SP/N 3/9/96)

Privacy Policy