ET-532 10-Channel Cordless Telephone
(430-1032)           Storing numbers in memory        Faxback Doc. # 31152

1.  With the handset's power on, press MEMORY.  The keypad lights and MEM
    appears on the display.

    NOTE:  While you are storing a number in memory, if you do not press
           any button on the keypad within about 9 seconds, the keypad
           light turns off and a buzz sounds.  You must press MEMORY again
           so the keypad lights before you can store the telephone number.

2.  Enter the phone number you want to store.  The number appears on the
    display.

    NOTES:  The phone does not dial the number at this point.

            If you enter a wrong digit, press FLASH/DEL to delete the last
            entered digit.

            If you enter more than 16 digits, the phone buzzes and the 
            display turns off.  To dial a number with more than 16 digits,
            see "Chain Dialing".

3.  Press MEMORY again.

4.  Enter the two-digit memory location number (01, 02 ..... 30) where you
    want to store the number.  The index number appears, and a long beep
    sounds.  The phone number is now stored in the memory.

5.  Pull out the memory index card at the bottom of the base.  Write the
    person's or company's name and index number on the sheet in pencil (in
    case you want to change it later).

6.  Repeat Steps 2-5 to store other telephone numbers.

NOTES:  If you receive a call while you are storing a number in memory,
        press TALK to answer the call.  After the call, begin again at 
        Step 1 to store the number.

        To change a phone number stored in memory, simply store a new
        phone number in that location.

        To clear a memory location so no number is stored there, press
        MEMORY twice, then press the location number.  A long beep 
        sounds.  The phone number is now cleared from the memory.

        If a buzz sounds, you did not successfully clear the 
        memory location.  Try the process again.

ENTERING A PAUSE IN A MEMORY NUMBER

In some telephone systems, you must dial an access code (9, for example)
and wait for a second dial tone before you can dial an outside number.  If
your phone is connected to one of these systems, you might want to enter a
pause at the appropriate point when you store a phone number in memory.

At the appropriate place in the number, press PAUSE to enter a 2-second
pause.  P appears.  For a longer pause, press PAUSE again.

NOTE:  Each PAUSE entry uses one digit of memory.

DIALING A STORED NUMBER

There are two ways to dial a stored number. 

METHOD 1

1.  Lift the handset from the cradle and press TALK so the keypad and TALK
    key light.

2.  When you hear a dial tone, press MEMORY, then press the number buttons
    for the correct memory location.  The stored number appears on the
    display, and the phone dials the stored number.

METHOD 2

1.  Lift the handset from the cradle and press TALK so the keypad and TALK
    key light.

2.  Press either the up or down SCROLL button to search for the desired
    stored number.  The selected number appears on the display.

3.  Press ENTER.  The phone dials the stored number.

CHAIN DIALING

When storing numbers for special services (such as alternate long distance
or bank-by-phone), store the service's main phone number in one memory
location and numbers for additional information in other memory locations.

To chain dial memory numbers, follow these steps.

1.  With the handset's power on, press MEMORY and the memory-location
    number for the service's main number.  The numbers appear.

2.  Wait for the service to answer.

    NOTE:  If you use pulse dialing to dial the service, be sure you have
           stored a * (tone) entry in the next memory location used to
           send the additional information.

3.  Press MEMORY and the numbers for the memory location where the 
    additional information is stored.  The numbers appear.

4.  To disconnect the call, press TALK so the TALK key does not light.

TEST STORED EMERGENCY NUMBERS

If you store an emergency service's number (police department, fire
department, ambulance) and you want to test the stored number, make the
test call during the late evening or early morning to avoid peak demand
periods.  Remain on the line to explain the reason for your call.


(SP/N 3/9/96)

Privacy Policy