Headset Cordless Telephone
(430-0569B)                 Operation                 Faxback Doc. # 19222

PUTTING ON THE HEADSET

Before you use the phone, place the headset on your head and adjust the
mouthpiece as necessary.

For best results, place the microphone 2 to 3 inches from your mouth.

MAKING/ANSWERING A CALL

To turn on the phone, set POWER to ON.   For best reception, fully extend
the base’s antenna and position it vertically.

To answer a call, press TALK/HANG UP when you hear the remote keypad ring.
The IN USE indicator lights.

To make a call, press TALK/HANG UP and listen for a dial tone.  Then enter
the desired phone number.

To hang up, press TALK/HANG UP.  The IN USE indicator turns off.

NOTES:  Set POWER to OFF when the remote keypad is away from the base to
        conserve battery power.  When you hear another phone on the same
        line ring, set POWER to ON and press TALK/HANG UP to answer the
        call.

        When you press a button, a single tone indicates that the phone
        accepts the command.  Three tones indicate that you pressed a
        button in error, you are out of range, or there is too much
        interference.  (You do not hear these tones if POWER is set to
        OFF.)

        If there is severe interference, the remote keypad sounds three
        tones to indicate that it cannot communicate with the base.  Before
        you press any key, move closer to the base.

        If the battery is low or interference is severe, the remote keypad
        might lose communication with the base and the call might
        disconnect.  This does not happen often, but if it does, return the
        remote keypad to the cradle for about 5 seconds.

Frequency Channels

This phone operates on one of four sets of frequencies.  If you experience
interference with the phone, you can exchange it for a model that operates
on a different set of frequencies.  If you decide to exchange the phone,
you must do it within 30 days of the original purchase date.

USING REDIAL

To quickly redial the last number dialed, simply press REDIAL.

The redial memory holds up to 16 digits, so you can redial long-distance or
local numbers.

The redial memory can also store PAUSE entries and switches from pulse to
tone dialing (see "Using Tone Services on a Pulse Line"),  see below.

Entering a Pause

With some telephone systems, you must dial an access code (9, for example)
and wait for a second dial tone before you can dial an outside number.

If your phone is connected to one of these systems, you might want to enter
a pause at the appropriate point in a number you plan to redial.  Press
REDIAL/PAUSE once to enter a 2-second pause.  To lengthen the pause in
2-second increments, press REDIAL/PAUSE additional times.

USING THE PRIVACY FEATURE

Press and hold down PRIVACY (on the upper left side of the remote keypad)
if you do not want the person on the other end of the phone line to hear
you as you talk to someone else in the room.  You can still hear the person
on the other end of the phone line.  Release PRIVACY to resume your phone
conversation.

USING THE VOLUME CONTROL

The volume control (on the lower left side of the remote keypad) is
especially helpful when the reception is weak.  Rotate VOLUME up to
increase the volume or down to decrease it.

USING FLASH

Use FLASH to perform the switchhook operation for special phone services
such as call waiting.

For example, if you have call waiting, press FLASH to answer a second call
without disconnecting the current call.  Press FLASH again to return to the
first call.

NOTES:  The redial memory does not store the FLASH entry or the digits you
        press after the FLASH entry.

        If you do not have any special phone services, pressing FLASH might
        disconnect the current call.

USING TONE SERVICES ON A PULSE LINE

Some special phone services, such as bank-by-phone, require tone signals.
If you have pulse service, you can still use these special tone services.
Follow these steps.

1.  Dial the service’s main number.

2.  When the service answers, press TONE #, then dial the additional
    numbers.  The phone sends these numbers as tone signals.

3.  When you complete the call, place the headset on the cradle or press
    TALK/HANG UP to disconnect the call.  The phone automatically resets
    to the pulse mode.


(EB 1/9/96)

Privacy Policy