This tutorial is divided into 3 sub-tutorials, each of which start with the same two steps:
For additional information on this product, see the links below:
| Step 1: Entering the Program Mode |
|
| While the clock appears on the display, press MENU. TEMPERATURE appears on the display. |
| Step 2: Selecting the TEMPERATURE Options |
 |
| Press the RIGHT
arrow key. INDOOR will appear on the display. Press
the UP or DOWN arrow to select INDOOR,
OUTDOOR, °C/°F, or REMOTE
CHANNEL. Go to Resetting Indoor/Outdoor to change the maximum or minimum temperatures. Go to Setting °C/°F to select Celsius or Fahrenheit. Go to Setting the Remote Channel for setting up your remote temperature sensor. Go to Exiting Program Mode to exit programming. |
In INDOOR mode, you can reset the minimum and maximum temperatures for the Weatheradio's location.
In OUTDOOR mode, you can reset the minimum and maximum temperatures for the remote sensor's location.
| Step 1: Selecting the Reset Maximum Temperature |
|
| Press the RIGHT arrow key. RESET MAX appears on the display. If you are in INDOOR mode, MAX and a small house with IN inside it (INDOOR icon) flashes. If you are in OUTDOOR mode, MAX and the word OUT with a roof over it (OUTDOOR icon) flashes. |
| Step 2: Resetting the Maximum Temperature |
 |
| Press the RIGHT arrow key to reset the maximum temperature. A beep sounds and the maximum temperature resets to --.- °F. |
| Step 3: Selecting the Reset Minimum Temperature |
 |
| Press the UP or DOWN arrows until RESET MIN appears on the display. MIN and the INDOOR and icon flash. |
| Step 4: Resetting the Minimum Temperature |
 |
| Press the RIGHT arrow key to reset the minimum temperature. A beep sounds and the minimum temperature resets to --.- °F. |
| Step 5: Exiting the Resetting Temperature |
 |
| Press the LEFT
arrow key twice. TEMPERATURE appears on the display. Go to Setting °C/°F to select Celsius or Fahrenheit. Go to Setting the Remote Channel for setting up your remote temperature sensor. Go to Exiting Program Mode to exit programming. |
| Step 1: Selecting the °C/°F Format |
|
| When °C/°F appears, press the RIGHT arrow key. °C appears on the display. |
| Step 2: Selecting °F |
 |
| Press the UP or DOWN arrow keys to select °F format. |
| Step 3: Confirming the Selection |
|
| Press the RIGHT
arrow key. Both indoor and outdoor temperatures appear in the selected format, and a
beep sounds. Press the LEFT arrow key twice. TEMPERATURE appears on the display. Go to Setting the Remote Channel for setting up your remote sensor. Go to Exiting Program Mode to exit programming. |
For the remote sensor to operate, both the sensor and the Weatheradio must be set to the same channel. If the Weatheradio does not display the remote temperature after about 2 minutes while the remote sensor is off (--.- appears), that channel is clear and free for use. If a remote temperature is displayed while the remote sensor is off, there is interference on that channel. To clear the interference, set the sensor and the Weatheradio to a different channel.
| Step 1: Selecting the Remote Channel Mode |
|
| Press the RIGHT arrow
key. When REMOTE appears on the display, then CHANNEL
appears on the display, press the RIGHT arrow key. Note: REMOTE and CHANNEL do not appear on the display at the same time. |
| Step 2: Finding the Remote Channel |
 |
| Press the UP
or DOWN arrow keys on the Weatheradio to select a channel (1-3)
that matches the channel set on the remote sensor. Note: The channel on the remote sensor is located underneath the batteries. |
| Step 3: Selecting the Remote Channel |
 |
| Press the RIGHT
arrow key when the desired channel appears. A beep sounds and REMOTE
CHANNEL flashes on the display again. Go to Exiting Program Mode to exit programming. |
| Step 1: Exiting the Program Mode |
|
| Press MENU to exit program mode. |
Copyright© RadioShack Corporation 2002. All rights reserved.
