Compaq Presario 1232 Notebook
(250-0327) Setup Utility Faxback Doc. # 48909
Press <F10> while the COMPAQ banner screen is displayed while booting to
enter the CMOS Setup program.
The Setup has six sections, MAIN, ADVANCED, SECURITY, POWER, BOOT, and
EXIT. Use the left and right arrow keys to access the separate sections.
Use the up and down arrow keys to access the items within the sections.
Use the plus and minus keys to change values. Pressing the <F9> key
recalls the system defaults.
THE MAIN MENU
---------------------------------------------------------------------------
<MAIN> ADVANCED SECURITY POWER BOOT EXIT
CPU Type: CYRIX MEDIAGXm
CPU Speed 233 MHz
System Time: [06:12:54]
System Date: [04/01/1998]
Primary Master 3251MB
Secondary Master CD-ROM
System Memory: 640 KB
Extended Memory: 31744 KB
BIOS version 1.05
---------------------------------------------------------------------------
F1 HELP ^v SELECT ITEM +/- CHANGE VALUES F9 SETUP DEFAULTS
ESC EXIT <- SELECT MENU ENTER SELECT SUBMENU F10 SAVE AND EXIT
---------------------------------------------------------------------------
From the MAIN menu, press the RIGHT ARROW key once to move to the ADVANCED
menu.
THE ADVANCED MENU
---------------------------------------------------------------------------
MAIN <ADVANCED> SECURITY POWER BOOT EXIT
Setup Warning
Setting items on this menu to incorrect values may cause your system to
malfunction.
I/O Device Configuration
Audio Options Menu
Large Disk Access Mode [DOS]
---------------------------------------------------------------------------
F1 HELP ^v SELECT ITEM +/- CHANGE VALUES F9 SETUP DEFAULTS
ESC EXIT <- SELECT MENU ENTER SELECT SUBMENU F10 SAVE AND EXIT
---------------------------------------------------------------------------
From the ADVANCED menu,selecting the I/O DEVICE CONFIGURATION option and
pressing <ENTER> will take you to the I/O DEVICE CONFIGURATION menu.
I/O DEVICE CONFIGURATION
---------------------------------------------------------------------------
MAIN <ADVANCED> SECURITY POWER BOOT EXIT
Serial Port A: [AUTO]
Parallel Port: [AUTO]
MODE: [Bi-Directional]
Floppy Disk Controller: [Enabled]
USB Controller: [Enabled]
Primary IDE Adapter: [Enabled]
Secondary IDE Adapter: [Enabled]
---------------------------------------------------------------------------
F1 HELP ^v SELECT ITEM +/- CHANGE VALUES F9 SETUP DEFAULTS
ESC EXIT <- SELECT MENU ENTER SELECT SUBMENU F10 SAVE AND EXIT
---------------------------------------------------------------------------
From the ADVANCED menu, selecting AUDIO OPTIONS MENU and pressing <ENTER>
will take you to the AUDIO OPTIONS menu.
AUDIO OPTIONS MENU
---------------------------------------------------------------------------
MAIN <ADVANCED> SECURITY POWER BOOT EXIT
SOUND: [Enabled]
Base I/O Address: [220-22F]
MPU I/O Address: [330-331]
Interrupt: [IRQ 5]
8 bit DMA channel: [DMA 1]
16 bit DMA channel: [DMA 5]
---------------------------------------------------------------------------
F1 HELP ^v SELECT ITEM +/- CHANGE VALUES F9 SETUP DEFAULTS
ESC EXIT <- SELECT MENU ENTER SELECT SUBMENU F10 SAVE AND EXIT
---------------------------------------------------------------------------
From the ADVANCED menu, press the RIGHT ARROW key once to move to the
SECURITY menu.
SECURITY MENU
---------------------------------------------------------------------------
MAIN ADVANCED <SECURITY> POWER BOOT EXIT
Set Supervisor Password: [Enter]
Password on boot: [Disabled]
Fixed disk boot sector: [Normal]
---------------------------------------------------------------------------
F1 HELP ^v SELECT ITEM +/- CHANGE VALUES F9 SETUP DEFAULTS
ESC EXIT <- SELECT MENU ENTER SELECT SUBMENU F10 SAVE AND EXIT
---------------------------------------------------------------------------
From the SECURITY menu, press the RIGHT ARROW key once to move to the POWER
menu.
POWER MENU
---------------------------------------------------------------------------
MAIN ADVANCED SECURITY <POWER> BOOT EXIT
Power Savings: [Customized]
Idle Mode: [OFF]
Suspend Timeout: [15 Minutes]
Resume On Time: [Off]
Resume Time: [00:00:00]
Hard Disk Timeout: [5 Minutes]
---------------------------------------------------------------------------
F1 HELP ^v SELECT ITEM +/- CHANGE VALUES F9 SETUP DEFAULTS
ESC EXIT <- SELECT MENU ENTER SELECT SUBMENU F10 SAVE AND EXIT
---------------------------------------------------------------------------
From the POWER menu, press the RIGHT ARROW key once to advance to the BOOT
menu.
BOOT MENU
---------------------------------------------------------------------------
MAIN ADVANCED SECURITY POWER <BOOT> EXIT
1. [DISKETTE DRIVE]
2. [ATAPI CD-ROM DRIVE]
3. [HARD DRIVE]
---------------------------------------------------------------------------
F1 HELP ^v SELECT ITEM +/- CHANGE VALUES F9 SETUP DEFAULTS
ESC EXIT <- SELECT MENU ENTER SELECT SUBMENU F10 SAVE AND EXIT
---------------------------------------------------------------------------
From the BOOT menu, press the RIGHT ARROW key once to move to the EXIT
menu.
EXIT MENU
---------------------------------------------------------------------------
MAIN ADVANCED SECURITY POWER BOOT <EXIT>
Exit Saving Changes
Exit Discarding Changes
Load Setup Defaults
Discard Changes
Save Changes
---------------------------------------------------------------------------
F1 HELP ^v SELECT ITEM +/- CHANGE VALUES F9 SETUP DEFAULTS
ESC EXIT <- SELECT MENU ENTER SELECT SUBMENU F10 SAVE AND EXIT
---------------------------------------------------------------------------
(RDS-07/27/98)
Privacy Policy