IBM Aptiva C66/S7H
(250-0458/0460)            Command Phrases            Faxback Doc. # 41186

Command Phrases For A Selected Routine

This section lists the areas covered by Voice Command Phrases for a routine
that has previously been selected. To see the commands used to perform a
particular function, refer to the following function that you would like to
perform.

Select The Next or Previous Routine

To select the next routine on the Routine side of the Routine Assistant
screen, say: NEXT or PREVIOUS with or without the word ROUTINE.

  Sample Phrases: Next
                  Previous
                  Previous Routine

Delete The Selected Routine

To delete the selected routine on the Routine side of the Routine Assistant
screen, say: DELETE with or without the word ROUTINE.

  Sample Phrases: Delete 
                  Delete Routine

Change The Name or Address of The Selected Routine

To change the name or address of a selected routine on the Routine side of
the Routine Assistant screen, say: CHANGE with either the word NAME,
ADDRESS or CODE.

The Change command will place the cursor in the field called out so you can
edit the contents of that field.  In this command ADDRESS and CODE both
refer to the Housecode/Unit code address field.

If you just want to rename the selected routine just say, RENAME. It does
the same thing as CHANGE NAME.

  Sample Phrases: Change Code
                  Change Address
                  Change Name
                  Rename

Change The Selected Routine Definition to On or Off

To change the On/Off definition of the selected routine on the Routine Win-
dow side of the Routine Assistant screen, say: CHANGE TO with the word ON
or OFF, or simply say the word ON or the word OFF.


  Sample Phrases: On
                  Change To Off
                  Off

Change The Selected Routine to a Fast or Standard Routine

To change a selected routine to a fast or standard routine, say either:
CHANGE (or CONVERT) TO with the word FAST or STANDARD with or without the
word ROUTINE or MAKE (or MAKE THIS A) with the word FAST or STANDARD with
or without the word ROUTINE.

  Sample Phrases: Change To Fast
                  Change To Fast Routine
                  Convert To Standard
                  Make Fast
                  Make This A Standard Routine

Command Phrases For A Selected Module Within A Routine

This section lists the areas covered by Voice Command Phrases for a module
within a routine that has previously been selected.  To see the commands
used to perform a particular function, refer to the following function that
you would like to perform.

Select a Module Within a Routine

To select a specific module within a Routine, say: SELECT and the MODULE
NAME, or simply say the MODULE NAME.

NOTE: If more than one module has the same name, the first one in the
      sequence is selected. Repeat the name to select the next one in the
      sequence.

  Sample Phrases: Lamp
                  Select Lamp

Select The Next or Previous Module Within a Routine

To select the next or previous module within a routine, say: NEXT or
PREVIOUS with or without the word MODULE.

Delete a Module Within a Routine

To delete a selected module within a Routine, say: DELETE and the word
MODULE, or simply say DELETE.

NOTE: Select YES in the Warning Dialog Box to delete the module.

Set a Time Delay for a Module Within a Routine

To set a time delay for a selected module within a Routine, say: SET TIME
DELAY, or simply say TIME DELAY.

Set The On or Off State of a Module Within a Routine

To set the On or Off state for a selected module within a Routine, say:
TURN ON or TURN OFF, or simply say ON or OFF.

Set The Dim Level of a Module Within a Routine

To set the dim level of a selected lamp module within a Routine, say: DIM
TO with a percentage (0-100) with or without the word PERCENT.

  Sample Phrases: Dim To 80
                  Dim To 25 Percent

Set The Dim Mode for a Module Within a Routine

To set the dim mode for a selected lamp module within a routine, say
either: BRIGHTEN THEN DIM or DIM WITHOUT BRIGHTENING.

When a routine is initiated, Brighten Then Dim will turn a lamp module on
to full (100%) brightness first, then dim it to the level set in the rou-
tine. Dim Without Brightening will turn a lamp module on to the dim level
set in the routine.

NOTE: See the help sections on Standard Routines and Fast Routines for the
      detailed operation of the Dim Mode button on lamp modules within a
      Fast or Standard routine.

  Sample Phrases: Brighten Then Dim
                  Dim Without Brightening

Setting a Time Delay

This section lists the Voice Command Phrases used to set a time delay for a
module within a routine.

To set a time delay while viewing the Time Delay window, say either of the
following: 1 Minute or simply, Minute
           2 Minutes
           3 Minutes
           4 Minutes
           5 Minutes
          10 Minutes
          15 Minutes
          20 Minutes
          25 Minutes
          30 Minutes
           1 Hour or simply, Hour
           1 and a half Hours or simply, Hour and a half
           2 and a half Hours or simply. 2 Hours
           3 Hours
           4 Hours
           5 Hours


(EB 8/20/97)