CD-3314 (140-0538) Operation Faxback Doc. # 7200
USING THE RADIO
WARNING: To protect your hearing, set VOLUME to its lowest setting before
you turn on the radio.
1. Set FUNCTION to RADIO. The PWR/BATT (Operation/Battery) indicator
lights and the radio turns on.
2. Set BAND to FM or AM
3. Set BEAT/MONO/STEREO by using these guidelines.
To listen to FM stereo, set it to either of the two STEREO positions.
The FM STEREO indicator lights when you receive an FM station in
stereo.
To listen to FM monaural, set it to MONO.
4. Adjust TUNING to the desired station.
NOTES: For the best AM reception, rotate the CD-3314 to position the
built-in AM antenna.
For the best FM reception, fully extend the telescoping antenna
and swivel it to the position that produces the best reception.
If FM stereo reception get noisy while BEAT/MONO/STEREO is set to
STEREO, set it to MONO. The sounds is no longer in stereo, but
reception improves.
5. Adjust VOLUME and TONE to the desired levels.
6. To turn off the radio, set FUNCTION to TAPE (RADIO OFF). The PWR/BATT
indicator turns off.
USING THE CD PLAYER
CAUTIONS: A sudden shock or jolt while a CD is playing might suddenly
change the speed of the CD's rotation or cause the CD player to
skip the track it is playing and, as a result, momentarily mute
or distort the sound. This is not a malfunction.
If you move the CD-3314 from a very cold room to a warmer one,
moisture can condense on the pickup lens, preventing proper
disc pay. If this happens, turn the CD player off then wait 30
minutes before attempting to operate it again.
LOADING/UNLOADING A CD
1. Set FUNCTION to CD. CD DISPLAY shows 00 for about 2 to 3 seconds and
the PWR/BATT indicator lights.
2. Press OPEN-CLOSE to open the CD compartment.
3. Place a CD in the compartment with the label facing up.
4. Press OPEN-CLOSE to close the compartment door. CD DISPLAY shows 00
for about 5 seconds and the CD momentarily spins. When the CD stops
spinning CD DISPLAY shows the total number of tracks.
5. To remove the CD, press (OPEN-CLOSE Selection), grasp the CD by its
edges, and carefully pull it out.
CAUTIONS: To prevent possible damage to the CD or the CD player, always
remove a loaded CD.
Only when it is stopped.
Before you move the CD-3314.
PLAYING A CD
WARNING: The CD player has a wide dynamic range. Do not turn the volume
too high during a program's soft sections or its sudden loud
sections might cause hearing discomfort. To protect your
hearing, set VOLUME to the lowest setting before you turn on
your CD-3314.
1. Press >II. The CD player begins playing the first track and CD
DISPLAY shows the current track number.
NOTE: To temporarily pause the CD, press > II. PAUSE and the track
number appear on the display and the CD stops playing. Press >II
again to resume play.
2. Adjust VOLUME and TONE to the desired levels.
3. To stop play before it automatically stops at the end of the last
track, press (stop button).
REPEAT PLAY
You can repeat a single track or all the tracks on a CD or in a programmed
sequence (see "Programmed Play").
To repeat a single track, before or during play, press REPEAT until
repeat one appears on the display.
To repeat the entire disc or a programmed sequence, before or during
play, repeatedly press REPEAT until Repeat all appears on the display.
To stop repeat play, press REPEAT until repeat all or repeat one
disappears from the display.
AUDIBLE SEARCH
To search forward on the CD, press and hold down >> during play. As you
hold down >>, the CD rapidly advances and you hear the music or
information at a faster speed. Release >> to resume normal play
For reverse search, press and hold down << during play. Release << to
resume normal play.
SKIP SEARCH
You can skip tracks in either direction on a CD or in a programmed
sequence (see "Programmed Play").
During play, press and release >>I to skip to the beginning of the next
track.
During play, press and release I<< to skip to the beginning of the
current track.
Repeatedly press >>I or I<< to skip forward or backward through
additional tracks.
NOTE: Pressing >>I while the last track is playing has no effect.
CUING
You can cue a track before you begin normal or programmed play or during
pause. To cue a desired track, press >>I or I<< until the desired track
number appears on the display. Then press >>I to play the track.
PROGRAMMED PLAY
Storing a Programmed Sequence
You can program up to 21 tracks on a CD to play in any sequence.
1. Press MEMORY while the player is stopped. OO appears on the display.
2. Repeatedly press >>I or I<< until the desired track number appears on
the display.
3. Press MEMORY again to store the displayed track. OO reappears on the
display.
NOTE: The memory location number does not appear on the display.
4. Repeat Steps 2 and 3 to store up to 21 tracks.
CAUTION: When all 21 memory locations are used, the first programmed
track reappears on the display. When this happens, any
additional track you enter replaces the displayed track.
NOTE: You can store a track more than once.
Reviewing a Programmed Sequence
To review a programmed sequence, while the CD is stopped, repeatedly press
MEMORY. The display shows the programmed CD track numbers in sequence.
Playing a Programmed Sequence
1. Press >II. As each programmed track plays, MEMORY and the track
number appear on the display.
2. To temporarily pause the CD, press >II. The CD stops playing and
PAUSE, MEMORY, and the track number appear on the display. Press
>II again to resume play.
3. To stop play before it automatically stops at the end of the last
track, press (stop button).
NOTE: If the memory has not been cleared, you can replay a program even
if the CD player is stopped and MEMORY does not appear on the
display. Simply press MEMORY. When the display shows the first
programmed track number, press >II.
Replacing Tracks in a Programmed Sequence
1. While the CD is stopped, repeatedly press MEMORY until the track
number you want to replace appears on the display.
2. Press >>I until the new track number appears on the display.
3. Press MEMORY again to store the displayed track in place of the
previous track.
Clearing a Programmed Sequence
Any of the following actions clears a programmed sequence.
Press OPEN-CLOSE to open the CD compartment door after the CD stops
turning.
Set FUNCTION to TAPE (RADIO OFF) or RADIO.
Disconnect the power source.
CD CARE TIPS
Even thought a compact disc is very durable, treat its surface with
care. Always handle a CD by the edges to avoid fingerprints and always
keep it in its protective case or sleeve when it is not in use.
Do not write on either side of the CD, particularly the non-label side.
(signals are read from the non-label side.)
Do not store CDs in high-temperature, high-humidity locations. The CDs
might warp.
Fingerprints and scratches on the CDs surface can prevent the laser beam
from correctly reading the digital information. To clean the CDs
surface, use a CD Cleaner Kit (such as Cat. No. 42-116).
Keep CDs dry. A drop of moisture can act as a lens and affect the laser
beam's focus. Remove moisture with a soft, dry cloth. Move the cloth
in straight lines, starting from the center and moving out toward the
outer edge. Do not move the cloth in circles. Be sure the CDs are fully
dry before you use them.
USING THE CASSETTE PLAYER
PLAYING A CASSETTE TAPE
1. Set FUNCTION to TAPE (RADIO OFF).
2. Press STOP/EJECT to open the cassette compartment door.
NOTE: To prevent the tape from getting tangled in the record/playback
mechanism, before you insert the cassette, take up any slack in the
tape by turning the cassette's hub. Avoiding touching the tape.
3. Insert a cassette tape with the side you want to play facing you,
the exposed tape edge down, and the full reel to the left. Then close
the compartment door.
4. To play the tape, press PLAY. The PWR/BATT indicator lights.
NOTE: To rapidly move the tape forward or backward, before or during
play, press F.FWD or REWIND.
5. Adjust VOLUME and TONE to the desired sound levels.
6. Press STOP/EJECT to stop the tape before it automatically stops when
it reaches the end. The PWR/BATT indicator turns off.
NOTE:
To temporarily pause play, press PAUSE. Press PAUSE again to resume
play.
RECORDING A CASSETTE TAPE
You can record from the CD player or radio.
CAUTION: You cannot press down RECORD when you load a cassette with the
erase-protection tab removed. Do not force down RECORD or you
might damage the recording mechanism (see "Preventing Accidental
Erasure").
NOTES: The CD-3314's Automatic Level Control (ALC) automatically adjusts
the recording level. VOLUME has no effect on recording.
Be sure the erase-protection tabs are in place on the cassette
tape you are using to record.
We recommend regular length (60-or 90-minute) cassette tapes. We
do not recommend long-play cassette tapes such as C-120s because
they are very thin and can easily tangle in the recording or
playback mechanism.
Tape quality affects the quality of the recording. For low-noise,
wide-range recordings, we recommend you use normal bias tape.
Most CDs and pre-recorded tapes contain copyrighted material.
Copying or dubbing of copyrighted materials is a violation of
federal copyright laws and could result in fines and/or
imprisonment.
RECORDING FROM THE CD PLAYER
1. Set FUNCTION to CD.
NOTE: Before you load a cassette tape, turn the cassette's hub to move
the tape past its leader.
2. Insert a blank cassette tape or one you want to record over into the
cassette compartment.
3. Load a CD into the CD player (see "Loading/Unloading a CD").
4. Press PAUSE then RECORD on the cassette tape deck. RECORD and PLAY
lock down.
5. Press >II twice on the CD player. The CD DISPLAY shows the first
track number.
6. Press PAUSE on the cassette tape deck then >II on the CD player. The
cassette deck starts recording and the CD begins playing. The CD
DISPLAY shows the current track number.
NOTE: To temporarily pause the recording, press PAUSE on the cassette
deck. Press PAUSE again to resume recording.
7. To stop recording, press STOP/EJECT on the cassette deck.
8. To stop the CD player before it automatically stops when it reaches
the end, press (stop button).
RECORDING FROM THE RADIO
1. Follow Steps 1 through 4 under "Using the Radio."
2. Insert a blank cassette tape or one you want to record over into the
cassette compartment.
3. Press RECORD on the cassette tape deck. RECORD and PLAY lock down.
The cassette deck starts recording from the radio.
NOTES: To reduce or eliminate a whistling sound sometimes produced when
recording from AM broadcasts, set BEAT/MONO/STEREO to any of the
three positions that give you the best sound quality.
To temporarily pause the recording, press PAUSE on the cassette
deck. Press PAUSE again to resume recording.
4. To stop recording before the tape automatically stops when it reaches
the end, press STOP/EJECT on the cassette deck.
5. To turn off the radio, set FUNCTION to TAPE (RADIO OFF).
TAPE CARE TIPS
Restoring Tape Tension and Sound Quality
After you play a cassette tape several times, the tape might become
tightly wound on the reels. This can cause playback sound quality to
deteriorate.
To restore the sound quality, fast-forward the tape from the beginning to
the end of one side, then completely rewind it. Then loosen the tape
reels by gently tapping each side of the cassette's outer shell on a flat
surface.
NOTE: Be careful not to damage the cassette when tapping it. Do not
touch the exposed tape or allow any sharp objects near the
cassette.
PREVENTING ACCIDENTAL ERASURE
Cassette tape have two erase-protection tabs - one for each side. To
protect a recording from being accidentally recorded over or erased, use a
screwdriver to remove one or both of the cassette tape's erase-protection
tabs.
WARNING: Removing the erase-protection tabs does not prevent a bulk
eraser from erasing a cassette.
NOTE: If you want to record on a tape side after you have removed the
erase-protection tab, place a piece of strong plastic tape over the
side's erase-protection hole. Be sure you cover only the hole
originally covered by the erase-protection tab.
ERASING A CASSETTE TAPE
If you no longer want a recording, you can record over it or erase it.
To erase a previously recorded section of a tape, simply record over it.
To erase the entire cassette tape, let the tape record silence to the end.
You can quickly erase both sides of a cassette tape using a bulk eraser
(such as Cat. No. 44-232, not supplied) available at your local Radio
Shack store.
(CJD/all-07/19/94)
Privacy Policy