CD-3680 Portable CD Player
(420-5075/76) Operation Faxback Doc. # 45636

Loading A CD

CAUTION: To help prevent dust from entering the CD player, always keep
the CD compartment cover closed except when loading or unloading
CDs.

1. Set OFF/RESUME/HOLD to OFF.

2. Slide OPEN in the direction of the arrow and lift the CD compartment
cover.

3. Carefully place a CD, label side up, over the center hub inside the CD
compartment. Then gently press the center of the CD until it snaps
down onto the center hub.

4. Close the compartment cover.

Playing A CD

WARNING: To protect your hearing if you are using earphones or headphones,
set VOLUME to its lowest setting before you play a CD.

Press PLAY/PAUSE. The CD player automatically turns on and 00 briefly
flashes on the display. Then > and the current track number appear and
Track 1 begins to play.

If you connected an earphone/headphones or amplified speakers to the CD
player's PHONES jack, use VOLUME on the CD player to adjust the volume.

If you connected the CD player to your home audio system or autosound
system using the LINE OUT jack, you must use the home audio or autosound system's volume control to adjust the volume.

If you connected an external power source, the CD player's buttons light
until you stop the CD and turn the CD player off, or the CD player turns
itself off automatically.

To temporarily stop play, press PLAY/PAUSE. > flashes. To resume play,
PLAY/PAUSE again.

When the last track finishes playing, the CD stops and the display alter- nately shows the total number of tracks and total playing time of the CD
for about 2 minutes, then the CD player automatically turns off. To turn
it off sooner, press STOP/CLEAR.

Digital Anti-Shock System (SAS^2)

Your CD player contains special circuits to overcome sound skipping prob-lems caused by shock or vibration. This means you can carry the CD player anywhere you go or use it in your vehicle. When you turn on the anti-shock system, the CD player continuo
usly saves 3 seconds (42-5075) or 10 seconds (42-5076) of music in memory. During a shock or vibration that would normally make a track skip or pause, the CD player plays directly from memory.

To turn on the anti-shock system, set DAS OUT/IN to IN. If the CD player
is playing a CD, the sound briefly stops, then DAS appears on the display and the sound continues.

Automatic Search Music System (ASMS)

You can use ASMS before or during regular or programmed play (see "Program-
med Play" below) to quickly locate any track on a CD.

While the CD is stopped, repeatedly press |<< or >>| to move backward or forward to the desired track. Press PLAY/PAUSE to play the track.

During play, press |<< to return to the beginning of the current track.
Press |<< twice to return to the beginning of the previous track. To
move to the beginning of the next track, press >>|.

Note: The CD player consumes additional battery power when you use the
anti-shock system. When you use the CD player in a stable
location, set DAS OUT/IN to OUT to save battery power.

To turn off the anti-shock system, set DAS OUT/IN to OUT. The sound
briefly stops, them DAS disappears from the display.

Locking The Controls

You can protect your CD player from accidental program changes by locking
all controls except OPEN, VOLUME, DAS OUT/IN (and OFF/RESUME/HOLD itself).

To turn on the control lock, set OFF/RESUME/HOLD. To turn it off, set
OFF/RESUME/HOLD to OFF.

Viewing The Elapsed Time

To display the current track's elapsed time, hold down MEMORY/E-BASS for
about 1 second. Hold down MEMORY/E-BASS again to return to the current
track display.

Turning E-Bass On and Off

To enhance the bass sound, press MEMORY/E-BASS. BASS appears on the
display. To turn the bass sound off, press MEMORY/E-BASS again, BASS
disappears from the display.

Audible Search

To search forward or backward during play, hold down >>| or |<<. The
CD plays rapidly and you hear the music at a high speed and low volume.
The current track's elapsed time appears on the display.

Release the button to resume normal play.

Note: If you hold down >>| while the last track is playing, audible
search starts again at the beginning of that same track. If you
hold down |<< during the first track, audible search stops at
the beginning of Track 1.

Pause/Cue

To temporarily pause play, press PLAY/PAUSE. > flashes on the display.
Press PLAY/PAUSE again to resume play.

You can also use PLAY/PAUSE to select (cue) a track before playing. When
the CD player is stopped, press >>| or |<< to select the track you want
to cue. Then press PLAY/PAUSE >|| twice. > flashes. When you are
ready to play the track, press PLAY/PAUSE >|| again.

Intro Scan

You can set the stereo to play the first 10 seconds of each track on the
CD, so you can find the track you want to listen to.

To begin scanning, repeatedly press PLAY MODE until 1 appears on the
display. Intro scan starts from the first track.

To return to normal play, repeatedly press PLAY MODE until 1 disappears.

Notes: Intro scan plays the tracks in the programmed order if you have
programmed a sequence (see "Programmed Play" below).

You can use |<< and >>| to skip through the tracks.

Repeat Play

You can repeat a single track on the CD, all tracks on the CD, or a
programmed sequence (see "Programmed Play" below).

To repeat a single track, press PLAY MODE once while the desired track
is playing. Symbol 1 appears on the display, and the CD player
continuously replays the track.

To repeat all tracks on a CD or in a programmed sequence, press PLAY
MODE twice. Symbol ALL appears on the display.

When the CD player reaches the end of the CD or the programmed sequence,
it continuously returns to the first track and replays all the tracks.

To cancel repeat play, repeatedly press PLAY MODE until symbol 1 and
symbol ALL disappear.

Random Play

In random play, the CD player plays all the tracks once in random order,
then automatically stops. To start random play, repeatedly press PLAY
MODE until R appears on the display.

Note: If you select random play during programmed play, the CD player
stops the programmed sequence and starts random play of all
tracks.

To cancel random play, repeatedly press PLAY MODE until R
disappears.

Programmed Play

You can program up to 24 tracks from the loaded CD to play in any order
you choose, and you can program the same track to play more than once.

Follow these steps to program and play a sequence.

1. While the CD is stopped, hold down MEMORY/E-BASS for about 3 seconds.
The display shows the selection number (01) and the track number (00),
and P flashes.

2. Repeatedly press either >>| or |<< to display the number of the first
track you want to program.

3. Press MEMORY/E-BASS to store the selected track number. The selection
number advances by one and the track number returns to 00.

4. Repeat Steps 2 and 3 for each track you want to program, up to 24
tracks.

Note: When you store the 24th track in memory, FULL appears.

5. To play the programmed sequence, press PLAY/PAUSE. P lights and the
first track in the sequence plays.

While the programmed sequence plays, you can use >>| to move forward
or |<< to move backward in the sequence.

6. After, the last programmed track ends, the CD before the end of the
sequence. press STOP/CLEAR.

Note: You can replay, check, or add to the programmed sequence within 2
minutes after play stops. Otherwise, the CD player turns off and
clears the programmed sequence.

To replay the programmed sequence, press PLAY/PAUSE.

To check the programmed sequence, press MEMORY/E-BASS. The display
shows the number of the first programmed track. Each time you press
MEMORY/E-BASS, the display shows the number of the next track in the
sequence.

To add to the end of a programmed sequence, repeatedly press MEMORY/E-
BASS until track number 00 appears. Then follow Steps 3 and 4.

To clear the programmed sequence from memory, press STOP/CLEAR twice
or open the CD compartment door.

Resume

You can set the CD player to remember the track it was playing when you
stopped the CD or it turned itself off. The way, when the play the CD
again, the CD player resumes playing at the beginning of that track.

To set the CD player to resume, set OFF/RESUME/HOLD to RESUME at any time.
Then, after you have pressed STOP/CLEAR to turn off the CD player., you
can simply press PLAY/PAUSE to resume play.

To cancel resume play, set OFF/RESUME/HOLD to OFF or open the CD compart-
ment.

Notes: If you press STOP/CLEAR very close to the beginning or end or a
track, the CD player might play the track before or after that
track instead when you press PLAY/PAUSE. This is not a
malfunction.

If you install a different CD while OFF/RESUME/HOLD is set to
RESUME, play might not start from Track 1 on the new CD. If
this happens, press STOP/CLEAR, set OFF/RESUME/HOLD to OFF,
then press PLAY/PAUSE again.

(LB/SM 12/02/97)