CD-3320 Portable AM/FM Stereo Cassette Recorder with CD Player
(140-0545) Radio/CD Operation Faxback Doc. # 34323
RADIO OPERATION
1. Set FUNCTION to RADIO. Then radio turns on.
2. Set BAND to AM or FM.
3. Adjust TUNING to the desired station.
NOTES: For the best AM reception, rotate the CD-3320 to position the built
in AM antenna.
For the best FM reception, fully extend the telescoping antenna and
swivel it to the position that produces the best reception.
If FM is selected, the CD-3320 automatically switches to stereo
when an FM broadcast is received in stereo.
4. Adjust VOLUME to a comfortable level.
5. Set E-BASS to MAX for an enhanced bass effect, to MIN for a diminished
bass sound, or to the center position for normal bass sound.
6. To turn off the radio, set FUNCTION to OFF.
CD PLAYER OPERATION
USING THE CD REMOTE CONTROL
The CD player's buttons also have corresponding buttons on the remote
control, and you can press either the CD player or remote control button to
control the function.
To use the remote control, point it directly at the infrared sensor on the
front of the CD-3320, then firmly press the desired button.
LOADING/UNLOADING A CD
1. Set FUNCTION to CD. - flashes, then stays lit on the display.
2. Press PUSH OPEN to open the CD compartment door.
3. Place a CD in the compartment with the label facing up.
4. Push the compartment door on PUSH TO CLOSE to close the door. - flashes
on the display, then the total number of tracks appears.
NOTE: If the CD has 20 tracks or more, 0 flashes on the display.
5. To remove the CD, press PUSH OPEN, grasp the CD by its edges, and
carefully pull it out.
NOTE: If the CD was playing, wait for it to stop turning before you press
PUSH OPEN to remove it.
PLAYING A CD
1. Press PLAY/PAUSE to play all the tracks in order starting with Track 1.
The CD PLAY indicator lights, and the current track number appears on
the display.
NOTE: Press PLAY/PAUSE to temporarily stop the CD. The CD PLAY
indicator flashes. Press PLAY/PAUSE again to resume playing the
CD. The CD PLAY indicator lights steadily.
2. Adjust VOLUME to a comfortable level.
3. Set E-BASS to MAX for an enhanced bass effect, to MIN for a diminished
bass sound, or to the center position for normal bass sound.
4. Press STOP/CLEAR (or STOP on the remote control) to stop playing the CD
before all tracks have played. 0 appears on the display.
RESETTING THE CD-3320
You might need to reset the CD-3320 if any of the following occur.
The CD-3320's display shows 0 and the CD player does not respond to any
buttons.
The CD-3320 is dropped or subjected to a physical or electrical shock.
CAUTION: This procedure clears all the information you have programmed
into the CD-3320. Use this procedure only when you are sure your
CD-3320 is not working properly.
1. Set FUNCTION to OFF, then set it to CD.
2. Press PLAY/PAUSE to play the CD.
AUTOMATIC SEARCH MUSIC SYSTEM (ASMS)
To skip backward or forward to another track while a CD is playing,
repeatedly press SKIP/SEARCH << or >> until the number of the track you
want to play appears. The CD player stops playing the current track, skips
to the selected track, then plays.
NOTES: If you use SKIP/SEARCH << or >> while CD is paused, the CD remains
paused when the CD player skips to the selected track.
If the CD is stopped, repeatedly press SKIP/SEARCH << or >> until the
display shows the number of the track you want to play, then press
PLAY/PAUSE. The CD player starts playing the selected track.
AUDIBLE SEARCH
To search for a particular section of a track while a CD is playing, press
and hold down SKIP/SEARCH << or >>. The CD player rapidly plays the CD
either backward or forward and automatically reduces the CD's volume. When
you hear the desired section, release SKIP/SEARCH << or >> to resume normal
play.
NOTES: If you press and hold SKIP/SEARCH << or >> while CD is paused, you
do not hear the CD play during the search and the CD remains paused
when you release SKIP/SEARCH << or >>.
If you reach the beginning of Track 1 while pressing and holding
down SKIP/SEARCH <<, the CD player pauses at the beginning of Track
1.
If you reach the end of the last track while pressing and holding
down SKIP/SEARCH >>, the CD player stops and 0 appears.
REPEAT PLAY
To repeat the entire CD, press REPEAT once before or during play. The
REPEAT indicator lights, and the CD player continuously replays the entire
CD.
NOTE: If you have programmed a sequence in memory (see "Programmed Play",
below), pressing REPEAT replays the entire sequence.
To cancel the repeat function, press REPEAT again. The REPEAT indicator
turns off.
PROGRAMMED PLAY
You can program up to 16 tracks on a CD to play in any sequence.
NOTE: Be sure the CD player is stopped before you program tracks.
1. Press SKIP/SEARCH << or >> to select the track you want to store in the
first memory location. The selected track number flashes.
2. Press MEMORY. The MEMORY indicator lights.
3. Repeat Steps 1 and 2 to program additional tracks.
NOTE: When all 16 memory locations are used, the track number on the
display does not change when SKIP/SEARCH << or >> is pressed.
4. Press PLAY/PAUSE. The tracks play in the programmed order. The
current track number appears on the display, and the CD PLAY and
MEMORY indicators light.
NOTE: During play, you can press SKIP/SEARCH << or >> to move through
the programmed sequence.
5. To clear the program from memory, press STOP/CLEAR (or STOP on the
remote control) twice.
CHECKING A PROGRAMMED SEQUENCE
When play is stopped, press MEMORY to display the programmed tracks in the
order they were entered. 0 appears on the display after the last
programmed track number.
ADDING TO THE PROGRAMMED SEQUENCE
You can repeat Steps 1 and 2 in "Programmed Play" to add to the end of the
programmed sequence.
NOTES: You can only add to a programmed sequence if you have fewer than 16
tracks programmed.
You cannot change a programmed track, or add an entry before or
between the programmed tracks.
(YO/EB 8/5/96)
Privacy Policy