CD-6600 Compact Disc Automatic Changer
(420-5059)                 Operation I                Faxback Doc. # 32150

CONNECTING HEADPHONES

You can connect a pair of headphones (not supplied) with a 1/4-inch plug
to the CD changer to listen to it in private.  Your local Radio Shack
store has a wide selection of headphones.

To connect headphones to the CD changer, insert the headphones' plug into
the CD changer's PHONES jack.  Then, when you play a CD, turn VOLUME
clockwise or counterclockwise to adjust the volume.

    NOTE:  VOLUME only affects the headphones' volume level, not the
           volume you hear through the receiver/amplifier's speakers.

Listening Safely

To protect your hearing, follow these guidelines when you use headphones.

    Set the volume to the lowest setting before you begin listening.
    After you begin listening, adjust the volume to a comfortable level.

    Do not listen at extremely high volume levels.  Extended high-volume
    listening can lead to permanent hearing loss.

    Once you set the volume, do not increase it.  Over time, your ears
    adapt to the volume level, so a volume level that does not cause
    discomfort might still damage your hearing.

BASIC OPERATION

    WARNING:  To protect your hearing, set VOLUME on the CD changer and
              the volume on your receiver or amplifier to its lowest level
              before you load and play a CD.

    CAUTION:  Do not set VOLUME on the CD changer or the volume on your
              receiver or amplifier too high while playing soft or quiet
              portions of a music program.  Due to the CD changer's wide
              dynamic range, the speakers or optional headphones might be
              damaged if the music program includes a sudden loud passage.

USING THE REMOTE CONTROL

Many of the CD changer's buttons also have a corresponding button on the
remote control, and you can press either the CD changer or remote control
button to control the function.

    NOTE:  You must turn on the CD changer by pressing POWER/STANDBY until
           POWER ON scrolls the display before you can use the remote
           control to operate the CD changer (see "Turning the CD Changer
           ON and Off", below).

           To use the remote control, point its front directly at the
           infrared sensor on the left side of the CD changer above the
           display, then firmly press the desired button or turn
           CATEGORY/DISC.

TURNING THE CD CHANGER ON AND OFF

To turn on the CD changer, either:

    Press POWER/STANDBY until POWER ON scrolls across the display.

    Make sure POWER/STANDBY is pressed in (to STANDBY), then press POWER
    on the remote control.

When you turn on the CD changer, the CD tray rotates to search for loaded
CDs.

    If there are loaded CD's, the display shows DISC, the current disc
    number, and each loaded CD's disc number surrounded by a graphic.

    If there are no loaded CD's, the display shows DISC 1, and NO DISC.

    NOTE:  If you connected the CD changer to a switched AC outlet and
           leave POWER/STANDBY pressed in, you can turn on the receiver or
           amplifier to turn on the CD changer.

To turn off the CD changer, either:

    Press POWER/STANDBY until GOOD-BYE scrolls across the display.

    Press POWER on the remote control.

    NOTES:  If you connected the CD changer to a switched AC outlet and
            leave POWER/STANDBY pressed in, you can turn off the receiver
            or amplifier to turn off the CD changer.

            If you do not plan to use the CD changer for a long time,
            disconnect it from the AC outlet.  The CD changer draws a
            small amount of AC power even when it is not turned on.

LOADING CDs

    IMPORTANT:  Make sure you have removed the shipping screw and sleeve
                from the bottom of the CD changer before you load and play
                CD's (see "Removing the Shipping Screw", on Faxback
                Doc. # 32149).

Follow these steps to load CD's.

1.  Turn on your receiver or amplifier.

2.  If necessary, Press POWER/STANDBY on the CD changer or POWER on the
    remote control to turn on the CD changer.

    NOTE:  Wait a few seconds until the CD changer displays DISC or NO
           DISC before continuing.

3.  Before you load a CD, assign a number to it in one of the following
    ways:

    On the remote control, turn and hold CATEGORY/DISC clockwise or
    counterclockwise until the disc number appears.

    Repeatedly press DISC SKIP DOWN or DISC SKIP UP on the CD changer
    until the disc number appears.

    Enter a 2-digit disc number using the DISC SELECT number keys on the
    CD changer or the number keys on the remote control.

    NOTE:  There are 60 disc numbers.  The bottom rows of the display show
           a semicircle around a disc number when a CD is loaded in that
           position.  If you choose a disc number that already has a CD
           loaded in it, the CD changer selects that CD.

4.  Press LOAD/EJECT on the CD changer.  The CD slot opens, LOAD DISC
    scrolls across the display, and the selected disc number flashes.

    To load a CD hold it vertically, then gently insert it about halfway
    through the CD slot, label side to the right, within 10 seconds.  The
    CD changer automatically pulls the CD inside.

    CAUTIONS:  Do not load anything other than 5-inch CD's into the CD
               changer.  Do not load single 3-inch CD's or 3-inch CDs with
               any type of adapter device.  This could damage the CD
               changer.

               Do not force the CD into the CD slot.

               Do not try to hold on to the CD or pull the CD out while
               the changer is pulling it in.

               To avoid pinching your fingers or damaging the CD or the CD
               changer, do not put your finger in the CD slot or the CD's
               center hole while inserting a CD.

    NOTE:  If the CD slot closes before you load the CD, simply press
           LOAD/EJECT again and insert the CD.

           When you load a CD, either ENTER CATEGORY or CATEGORY IS and a
           previously assigned category and subcategory name (If any)
           scrolls across the display twice.  To assign a category and
           subcategory name to the CD, see "Using CATEGORY and Subcategory
           Names", on Faxback Doc. # 32151.

5.  Repeat Steps 3-4 to load more CD's (up to 60).

SELECTING A CD

Select a CD by entering its disc number using any of the following
methods.

    On the remote control, turn and hold CATEGORY/DISC clockwise or
    counterclockwise until the disc number appears.

    Repeatedly press DISC SKIP DOWN or DISC SKIP UP on the CD changer
    until the disc number appears.

    Enter a 2-digit disc number using the DISC SELECT number keys on the
    CD changer or the number keys on the remote control.

    NOTE:  If you select a number that does not have a disc assigned to
           it.  NO DISC appears.

EJECTING CD's

1.  With play stopped, select the CD you want to eject.

2.  Press LOAD/EJECT on the CD changer.  EJECTING DISC and the disc number
    scroll across the display, the CD slot opens, and the CD changer
    ejects the CD.

    CAUTION:  Do not try to load a CD while EJECTING DISC and the disc
              number are scrolling across the display.  This can damage
              the CD changer and the CD.

3.  Gently remove the CD from the CD slot within 10 seconds.

    CAUTIONS:  Do not try to hold on to the CD or pull the CD out while
               the CD changer is ejecting it.

               To avoid pinching your fingers or damaging the CD or the CD
               changer, do not put your finger in the CD slot or the CD's
               center hole while removing a CD.

               If you do not remove the CD within 10 seconds, the CD
               changer automatically pulls it in again.  Never try to
               remove the CD while the CD changer is pulling it in.  Wait
               until the CD is fully loaded, then press LOAD/EJECT again.

4.  Repeat Steps 1-3 to remove more CD's.

PLAYING CD's

1.  If necessary, turn on the CD changer.

    NOTE:  Wait a few seconds until the CD changer displays DISC, the
           current disc number, the total number of tracks on the CD, and
           the total playing time of the CD before continuing.

2.  Select the CD you want to play.

    NOTE:  If you select a number that does not have a disc assigned to
           it, NO DISC appears.

3.  Set your receiver's or amplifier's audio input switch to the position
    that matches the jack where you connected the CD changer (for example,
    CD, AUX, or TAPE).

4.  Press PLAY/PAUSE.  > PLAY appears, and SEARCHING DISC and the CD's
    number scroll across the display.  After a few seconds, the selected CD
    begins to play from Track 1.

While a CD plays, the CD changer displays:

    The current disc number (blinking inside the graphic)

    The current disc number and track number

    The current index number if the CD has index numbers (numbers that
    mark sections within a track) or 1 if the CD does not have index
    numbers

    Elapsed time for the current track (in minutes and seconds)

    NOTES:  If DISC ERROR scrolls across the display or if the graphic
            around the current disc number blinks, the CD might be loaded
            incorrectly or scratched.  Press LOAD/EJECT on the CD changer
            to eject the CD, then fix and reload it.

            A sudden shock or jolt while a CD is playing might suddenly
            change the CD's rotation speed or make the CD changer skip the
            current track.  This might momentarily mute or distort the
            sound.  This is not a malfunction.

            To temporarily stop play, press PLAY/PAUSE.  > PLAY flashes on
            the display.  To resume play, press PLAY/PAUSE again.

            Although the CD changer displays any index numbers a CD has,
            the CD changer cannot automatically skip to their location.

5.  To stop play, press STOP.

DISPLAYING INFORMATION ABOUT CDs

To display additional information about the current CD, repeatedly press
DISPLAY while the CD is playing.  Each time you press DISPLAY, the
information changes in this order:

1.  Category name assigned to the CD (if any)

2.  Subcategory name assigned to the CD (if any)

3.  Remaining time for the current track (in minutes and seconds)

4.  Remaining time for the entire CD (in minutes and seconds)

5.  Elapsed time for the current track (in minutes and seconds)

    NOTES:  If the current track number is 56 or higher, the CD changer
            displays --, -- instead of the remaining time for the current
            track.

            You cannot display the remaining time for the entire CD during
            programmed play.

            When you press STOP, the CD changer displays the selected CD's
            total play time and total number of tracks.


(EB 4/22/96)
(BR 4/3/96)

Privacy Policy