DMP-2100 (26-1256) Control Codes Faxback Doc # 4601
* If Function Selection Switch 6 is set to OFF side, one line feed
operation is performed at the same time.
*** These codes may not be able to send to the printer by your computer.
In this case, use system command to send them.
---------------
|Control Codes|
---------------
DEC. HEX.
DP Mode
WP Mode
GR Mode
Remarks
---------------------------------------------------------------------------
00 00
DP: Ignored
WP: Ignored
GR: Ignored
---------------------------------------------------------------------------
8 n 08 n
DP: Backspace. (n=Binary) n:Backspaced dot number
WP: Backspace. (n=Binary) n:Backspaced dot number
GR: Ignored. Receives n as character data.
Remarks: ***
---------------------------------------------------------------------------
10 or 138 0A or 8A
DP: Executive Line Feed. Executive LV in accordance with information
latched
WP: Full Line Feed. Executive.
GR: 11/108" Line Feed. Executive... 8A hex. 138 dec.
Remarks: *LF/NL Selectable. ***
---------------------------------------------------------------------------
12 0C
DP: Form Feed
WP: Form Feed
GR: Form Feed
Remarks: LF/NL Selectable
---------------------------------------------------------------------------
13 or 141 0D or 8D
DP: Carriage Return (When NL, LF pitch is latched one)
WP: Carriage Return (When NL, LF pitch is 1/6" (1/8") per line.)
GR: Carriage Return only 0D Hex. (When NL, LF pitch is 7/72" per line.)
Remarks: NL/CR selectable
---------------------------------------------------------------------------
14 0E
DP: End Underline
WP: End Underline
GR: Ignored
---------------------------------------------------------------------------
15 0F
DP: Start Underline
WP: Start Underline
GR: Ignored
---------------------------------------------------------------------------
18 12
DP: Select Graphics Mode
WP: Select Graphics Mode
GR: Ignored
---------------------------------------------------------------------------
19 13
DP: Ignored
WP: Select DP Mode
GR: Ignored
---------------------------------------------------------------------------
20 14
DP: Select WP Mode
WP: Ignored
GR: Ignored
---------------------------------------------------------------------------
27 n 1B n
DP: Proportional spacing (2nd byte is dot columnÿ#)
WP: Proportional spacing (2nd byte is dot columnÿ#)
GR: Ignored
Remarks: 1ónó9. ***
---------------------------------------------------------------------------
27 14 1B 0E
DP: Start Elongation
WP: Start Elongation
GR: Start Elongation
---------------------------------------------------------------------------
27 15 1B 0F
DP: End Elongation
WP: End Elongation
GR: End Elongation
---------------------------------------------------------------------------
27 16 n1 n2 1B 10 n1 n2
DP: Positioning (3 Pitches are available)(n1,n2 indicate dot position from
Home pos.)
WP: Positioning (3 Pitches are available)(n1,n2 indicate dot position from
Home pos.)
GR: Positioning (3 Pitches are available)(n1,n2 indicate dot position from
Home pos.)
Remarks: n1, n2: Binary value. ***
---------------------------------------------------------------------------
27 17 1B 11
DP: Select Proportional Character
WP: Select Proportional Character
GR: Ignored
---------------------------------------------------------------------------
27 18 1B 12
DP: Select Correspondence Character-10
WP: Select Correspondence Character-10
GR: Ignored
---------------------------------------------------------------------------
27 19 1B 13
DP: Select Standard Character-10
WP: Select Standard Character-10
GR: Ignored
---------------------------------------------------------------------------
27 20 1B 14
DP: Select Condensed Character
WP: Select Condensed Character
GR: Ignored
---------------------------------------------------------------------------
27 23 1B 17
DP: Select Standard Character-12
WP: Select Standard Character-12
GR: Ignored
---------------------------------------------------------------------------
27 28 1B 1C
DP: Set Half Forward Line Feed (No motion)
WP: Half Forward Line Feed (Executive)
GR: Ignored
---------------------------------------------------------------------------
27 29 1B 1D
DP: Select NLQ Compressed Character
WP: Select NLQ Compressed Character
GR: Ignored
---------------------------------------------------------------------------
27 30 1B 1E
DP: Set 1/2 Reverse LF
WP: Perform 1/2 Reverse LF
GR: Ignored
---------------------------------------------------------------------------
27 31 1B 1F
DP: Start Bold
WP: Start Bold
GR: Ignored
---------------------------------------------------------------------------
27 32 1B 20
DP: End Bold
WP: End Bold
GR: Ignored
---------------------------------------------------------------------------
27 49 1B 31
DP: 1/20 (1/120") Forward Line Feed (Executive)
WP: 1/20 (1/120") Forward Line Feed (Executive)
GR: 1/20 (1/120") Forward Line Feed (Executive)
---------------------------------------------------------------------------
27 52 n 1B 34 n
DP: Form Feed Set
WP: Form Feed Set
GR: Form Feed Set
---------------------------------------------------------------------------
27 54 1B 36
DP: Set Full Forward Line Feed (No motion)
WP: Ignored
GR: Ignored
---------------------------------------------------------------------------
27 56 1B 38
DP: Set 3/4 Forwrd Line Feed (No motion)
WP: 3/4 Forward Line Feed (Executive)
GR: Ignored
---------------------------------------------------------------------------
27 71 1B 47
DP: 4/5 (2/15") Forward Line Feed (Executive)
WP: 4/5 (2/15") Forward Line Feed (Executive)
GR: 4/5 (2/15") Forward Line Feed (Executive)
---------------------------------------------------------------------------
27 73 n1 n2 1B 49 n1 n2
d1 d2 d2 d1 d2 d2
DP: High Resolution Graphics (n1,n2 indicate point column length)
(d1,d2,d3,... are Image data)
WP: High Resolution Graphics (n1,n2 indicate point column length)
(d1,d2,d3,... are Image data)
GR: High Resolution Graphics (n1,n2 indicate point column length)
(d1,d2,d3,... are Image data)
---------------------------------------------------------------------------
27 75 1B 4B
DP: Insert New Paper
WP: Insert New Paper
GR: Insert New Paper
---------------------------------------------------------------------------
28 n1 n2 1C n1 n2
DP: Repeat Print Data (Undefined code is changed to X)
WP: Repeat Print Data (Undefined code is changed to X)
GR: Repeat Print Data (If MSB=0, Data is ignored)
---------------------------------------------------------------------------
30 1E
DP: Ignored
WP: Ignored
GR: End Graphic Mode
---------------------------------------------------------------------------
127 7F
DP: Ignored
WP: Ignored
GR: Ignored
---------------------------------------------------------------------------
255 FF
DP: Ignored
WP: Ignored
GR: (Printing Data)
---------------------------------------------------------------------------
Other Codes in Function Area(02 to 1F hex)
DP: Prints "X" marks
WP: Prints "X" marks
GR: Ignored
---------------------------------------------------------------------------
Other Codes in Function Area (80 to 9F hex)
DP: Prints "X" marks
WP: Prints "X" marks
GR: (Printing Data)
---------------------------------------------------------------------------
(tlc-8/06/93)
Privacy Policy