Citizen PROjet II (260-2957) Printer Setup Faxback Doc. # 14702
Factory Settings
When you receive the printer, its basic operating parameters are already
set with pre-defined values (default values). These factory setting will
probably meet your requirements. If they do not, you can change them,
using the SET-up procedure.
CAUTION: Always switch off the printer before changing the positions of
the SET-UP selectors, as their position is read only at printer
switch-on.
The factory settings, indicated by the OFF position of the selectors, are:
Feature Default Value
Font Courier 10
Print Style Upright
Print Pitch Normal
Print Orientation Portrait
Print Quality Letter Quality
Paper Handling Paper tray
Perforation Skip Enabled
Text Scale Mode Disabled
Graphic Density 75 dpi
Automatic Line Feed Disabled (CR=CR)
Ink Detection Enabled
Ink Save Mode (Graphics) Enabled
Ink Save Mode (Text) Enabled
Paper Size Letter (8.5 x 11
inches)
Character Set CP 437 International
Parameter Selection Procedure
Access to the SET-UP Selectors
CAUTION: To redefine the programmable parameters using the printer SET-UP
procedure, the printer must be switched off.
Open the top cover of the printer and the selector cover. On the inside
of the top cover, there is an engraved template which indicates the
parameter assigned to each selector. The names of the parameter groups
are also engraved on the inside of the selector cover.
How to Select the Parameter Settings
Each selector has two positions:
OFF : down (default position)
ON: up (alternative value for each specific parameter).
To alter the setting of the parameter(s), just change the position(s) of
the specific selector(s).
Termination of SET-UP Process
Once you have completed the selection of the parameter values you require,
close the selector cover and the top cover, then switch on the printer.
Each time you turn on the power, the printer "reads" the position of the
selectors and will be ready to print with the features you have defined.
Programmable Features
The 33 selectors are assigned to the programmable parameters singly, or in
some cases, in groups (for FONT, PAPER FORMAT, CHARACTER SET). Starting
from the left, the selectors are designated as follows:
A group of six selectors, numbered 1 to 6, which select the font.
Fourteen selectors, indicated alphabetically, which select individual
print attributes and features.
A group of three selectors, numbered 1 to 3, which select the paper
format.
A group of six selectors, numbered 1 to 6, which select the character
set.
A group of four selectors, numbered 1 to 4, which are reserved.
Resident Emulation (HP Desk Jet Plus)
Starting from the leftmost selector, the following parameters can be
defined:
FONT
The first six selectors on the selector bar define the print font to be
used. When selecting a resident font other than the default value
(COURIER 10), ONLY the specific selector should be raised; the other
five other five MUST all remain down.
1 2 3 4 5 6
COURIER 10
COURIER 16.6 ON
LETT. G. 10 ON
LETT. G. 12 ON
LETT. G. 16.6 ON
TIMES NORDIC ON
EXTERNAL FONTS ON
NOTE: For information on the resident fonts available, and their
characteristics, see Appendix E.
Print attributes and other features
The features assigned to selectors A to N, engraved on the inside of the
front cover are the alternative parameter values; i.e., they are the
values implemented when the corresponding selector is set in its ON
position.
ITALIC A
COMPRESSED B
LANDSCAPE C
DRAFT D
MANUAL FEED ENABLED E
PERFORATION SKIP F
DISABLED
TEXT SCALE MODE G
GRAPHIC DENSITY 300 DPI H
CR=CR+LF I
INK DETECTION DISABLED L
INK SAVE MODE (GRAPHICS) M
DISABLED
INK SAVE MODE (TEXT) N
DISABLED
RESERVED O
RESERVED P
The implementation of parameters A, B and C will depend on the font
selected with the first six selectors on the selector bar. If, for
example, the Times Nordic font is selected (selector 6 ON, selectors 1, 2,
3, 4 and 5 OFF), the selection of Landscape (selector C ON) will be
ignored.
Similarly, if an optional font containing only upright characters is
selected from a font card, the selection of Italic (selector A ON) will
have no affect.
Selector Feature OFF ON
A Print Style Upright Italic
B Print Pitch Normal Compressed
C Print Orientation Portrait Landscape
D Print Quality Letter Quality Draft
E Paper Feed Paper tray Manual
Device
F Perforation Skip* Perforation Skip Perforation
enabled (BOF=.5in; Skip disabled
TOF=.5 in) (BOF=.5 in;
TOF=0 in)
G Text Scale Mode Text Scale Mode Text Scale
** disabled Mode enabled
H Graphic Density 75 dpi 300 dpi
***
I Automatic Line Only carriage Carriage
Feed (CR=CR) return with
automatic line
feed (CR=CR+LF)
L Ink Detection Enabled Disabled
(ON LINE LED flashes
where there is no more
ink in the print head)
M Ink Save Mode Enabled Disabled
(Graphics)
N Ink Save Mode Enabled Disabled
(Text)
O Not currently assigned to any
Reserved resident parameter. The position
P of these selectors should not be
altered.
* Perforation Skip - see also command code ESC & I n L, Appendix F
** Text Scale Mode - see also command code ESC & k 6 W, Appendix F
***Graphic Density - see also command code ESC * t n R,Appendix F
Paper
Position the three selectors as indicated in the following diagram to
select the paper size you require (Selector 3 in ON position=default
value - Letter):
1 2 3
A4
LETTER ON
LEGAL ON
ENVELOPE ON ON
FREE ON ON ON
Character set
Set the six selectors as indicated in the following diagram to select the
character set you require (all selectors in OFF position=default value -
CP 437 International equivalent to Hewlett -Packard's PC-8):
1 2 3 4 5 6
CP 437 INTERNATIONAL
HP ROMAN 8 ON
PC 8 DENMARK/NORWAY ON
PC 850 (MULTILINGUAL) ON ON
ECMA94 - LATIN 1 ON
ISO4 - UNITED KINGDOM ON ON
ISO 21 - GERMANY ON ON
ISO 69 - FRANCE ON ON ON
ISO 15 - ITALY ON
ISO 60 - NORWAY ON ON
ISO 61 - NORWAY 2 ON ON
ISO 11 - SWEDEN NAMES ON ON ON
ISO 10 - SWEDEN ON ON
ISO 17 - SPAIN ON ON ON
ISO 6 - USASCII ON ON ON
ISO 2 - IRV ON ON ON ON
ISO 16 -PORTUGAL ON
ISO 14 - JIS ASCII ON ON
LEGAL ON ON
CP 860 - PORTUGAL ON ON ON
DANISH OPE ON ON ON
UNIX INTERNATIONAL ON ON ON
DANISH OPE II ON ON ON
SPAIN II ON ON ON ON
CP 863 - FRENCH CANADIAN ON ON
PC WIN (ANSI WINDOWS 3.1) ON ON ON
CP 852 ON
ISO 8859/2 ON ON
PC WIN (EAST EUROPEAN WIN 3.1) ON ON
CP 857 ON ON ON
ISO 8859/9 ON ON
PC WIN (TURKISH WINDOWS 3.1) ON ON ON
CP 866 ON ON ON
CP 855 ON ON ON ON
ISO 8859/5 ON ON
PC WIN (CYRILLIC WINDOWS 3.1) ON ON ON
CP 210 ON ON ON
CP 851 ON ON ON ON
ISO 8859/7 ON ON ON
PC WIN (GREEK WINDOWS 3.1) ON ON ON ON
CP 862 ON ON ON ON
ISO 8859/8 ON ON ON ON ON
DEFAULT SET IN CARD ON ON ON ON ON ON
Reserved
These four selectors (1 to 4) are not currently assigned to any parameters
in the resident emulation.
1 RESERVED
2 RESERVED
3 RESERVED
4 RESERVED
CAUTION: The position of these selectors should NOT be changed.
(LB/all-04/21/95)
Privacy Policy